Makita PDC1200 Betriebsanleitung Seite 14

Overdischarge protection
When the battery capacity is not enough, the tool or
machine stops automatically and an indicator lamp
blinks when you press the power button. In this case,
remove the battery from the tool or machine and charge
the battery.
Using the adapter pocket
CAUTION:
Do not use this unit with the cord
fixed using the hook and loop fastener of the
adapter pocket.
You can put the adapters into the adapter pocket as
shown in the figure.
► Fig.5: 1. Adapter 2. Adapter pocket
ASSEMBLY
CAUTION:
Always be sure that the unit is
switched off before carrying out any work on the
unit.
Assembling the unit
1. Attach the battery to the base plate of the shoulder
harness assembly as shown in the figure.
► Fig.6: 1. Battery 2. Base plate
CAUTION:
Make sure that the battery is
securely fixed to the base plate. Otherwise, the
battery may fall when you wear the unit or use the
unit, and cause an injury. If you can see the red indi-
cator as shown in the figure, the battery is not locked
completely.
► Fig.7: 1. Red indicator
CAUTION:
Be careful not to pinch your fin-
gers or thumbs between the battery and the base
plate when attaching the battery.
CAUTION:
When removing the battery, press
the lock button while holding the handle firmly.
Before removing the battery, set the waist belt to
the lowest position.
► Fig.8: 1. Handle 2. Lock button
2. Adjust the position of the waist belt. Pull up the
height adjustment lever, then adjust the position of the
waist belt by sliding the base plate, and then return the
lever.
► Fig.9: 1. Height adjustment lever 2. Base plate
3. Waist belt
CAUTION:
When adjusting the position of the
waist belt, be sure to lay down the unit so that the
battery faces downward as shown in the figure.
NOTICE:
If the height adjustment lever is loose,
tighten the nut of the height adjustment lever.
When tightening the nut, do not tighten it excessively.
Otherwise, the height adjustment lever will not move.
► Fig.10: 1. Nut
NOTE: If it is difficult to slide the base plate, lift up
the stand slightly so that the stand does not touch the
ground, and then slide the base plate.
3. Attach the adapter pocket to the waist belt with the
hook and loop fastener as shown in the figure.
► Fig.11: 1. Adapter pocket
NOTE: The adapter pocket can be attached on either
left or right side of the waist belt.
4. Adjust the width of the shoulder harness using the
width adjustment belt.
► Fig.12: 1. Width adjustment belt
5.
Put on the unit, then lock the buckle of the waist
belt, and then adjust the length of the waist belt.
► Fig.13: 1. Buckle
NOTE: You can fold and fix the belt with the hook and
loop fastener as shown in the figure.
► Fig.14: 1. Belt
6. Adjust the length of the shoulder harness.
► Fig.15: 1. Shoulder harness
NOTE: You can fold and fix the belt with the hook and
loop fastener as shown in the figure.
► Fig.16: 1. Belt
CAUTION:
When setting down the unit, place
the unit on a flat and stable surface so that the
unit does not fall.
When setting down the unit, unlock the buckle of the
waist belt, and then set down the unit slowly.
► Fig.17: 1. Buckle
OPERATION
CAUTION:
When wearing the unit, be sure
to put shoulder harness on your both shoulders.
Otherwise, the unit may fall when you wear the unit or
use the unit, and cause an injury.
CAUTION:
When wearing the unit, be sure to
wear the unit on your back. Otherwise, the unit may
fall during operation and cause an injury.
CAUTION:
Always switch off the tool or
machine before turning on the unit, or connecting
the plug of the adapter or power tool/machine
to the socket of the battery. Otherwise, the tool or
machine may start suddenly and cause an injury.
NOTE: The adapter for 18 V is not available for this
unit.
14 ENGLISH