Herunterladen Inhalt Inhalt Diese Seite drucken

Bosch AquaWash&Clean BWD4 Serie Gebrauchsanleitung Seite 17

Vorschau ausblenden Andere Handbücher für AquaWash&Clean BWD4 Serie:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 1
Small nozzle
18
19
Crevice nozzle
Telescopic suction tube
20
21
Suction hose
Dust bag holder
22
23
Water filter module:
A Filtration unit
B Partition
Container
24
25
Cleaning liquid container
Spray unit – suction hose handle attachment
26
27
Large atomizing nozzle
Small atomizing nozzle
28
29
Water pick up nozzle (BWD41720, BWD420HYG,
BWD421PET, BWD421PRO)
Rubber slat to the large atomizing nozzle
30
Washing set
31
Foam filter I (installed in the vacuum cleaner)
32
Foam filter II (installed in the vacuum cleaner)
33
Motor filter (installed in the vacuum cleaner)
34
EPA/HEPA outlet filter (installed in the vacuum cleaner)
35
Preparing the vacuum cleaner for
operation
1 Insert the end of the suction hose to the vacuum cleaner
opening so that the markings
vacuum cleaner housing are opposite each other and turn
the hose clockwise to the position
2 Connect the other end of the hose (handle) with the
telescopic suction tube.
3 Hold the ring on the pipe and set chosen length putting it
in or out.
4 Assemble the appropriate nozzle or brush to the other
end of the suction tube.
5 Use the following nozzles and brushes for traditional using
the water filter module: combination carpet & floor brush with
small objects separator, small nozzle, small brush, crevice
nozzle, mattress nozzle, parquet brush or turbo brush.
6 You may assemble a basket for picking up small objects
in the combination brush with small item separator. In order
to do so remove the basket cover and insert the basket.
7 To clean hard surfaces – wooden floors, plastic floors,
ceramic tiles etc. pull out the brush by pressing the switch on
the nozzle according to the figure
8 The vacuum cleaner is equipped with an accessory
compartment. The compartment opens/closes with the use
of a slider. To open/close the compartment side the slider
downwards/upwards and take out/ put away the desired nozzle.
9 The vacuum cleaner may be stored in a horizontal
14
B
on the hose end and on the
.
.
position; in order to this, place the fastening hook of the
combination nozzle/brush into its fastening. The hose may
be left attached to the vacuum cleaner, but it is important to
pay attention not to leave it heavily bent during storage.
10 Close the lid.
11 Grab the plug (4) and pull the cord out of the vacuum
cleaner.
Plug in the appliance.
Before switching on the vacuum cleaner
with the on/off button (8), make sure that the
appropriate module is installed in the container
(see section C, E, or F).
12 Switch on the vacuum cleaner by pressing the "on/off"
button (8).
In order to prepare the vacuum cleaner for wet operation
additionally:
13 Assemble the spray unit – the suction hose handle
attachment (26).
Attach the hose fastenings to the suction hose and the
telescopic suction tube.
14 Attach the end of the hose (sleeve) to the telescopic
suction tube and insert the other end of the hose in the small
atomizing nozzle or the large atomizing nozzle until you hear
a characteristic click.
15 Use the following nozzles for the wet vacuuming and wet
cleaning function or to pick up water: large atomizing nozzle,
small atomizing nozzle or the water pick up nozzle.
16 Slide the stub pipe valve plug downwards.
Insert the stub pipe of the hose to the valve in the
vacuum cleaner housing.
Make sure the stub pipe fastenings snap shut.
In case of difficulties in connecting the above
mentioned elements moisten the gaskets e.g.
with technical vaseline, water, etc.
Vacuum cleaner functions
TRADITIONAL CLEANING WITH DUST BAG
1 Press and hold the container lid opening button (2) and
lift the container lid.
2 Put the holder (22) into the container. Make sure the
holder is inserted correctly in the container guide slots and
the safety lock is engaged. Unfold the bag in the container.
Do not put holder into a wet container.
Thoroughly dry a wet container. Dust bag must
not get wet.
3 Cover the container with the filtration unit.
If the holder is not attached properly, the safety
lock will prevent covering the container with
the filtration unit.
C

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis