Arming/Disarming An Ids - Honeywell Insertic-Serie Montage- Und Bedienungsanleitung

10
10.2 AC Function
(Door release)
- Hold data carrier in the reading range (and/or enter PIN).
- Acknowledgment occurs.
Optical Authorised
Ready (green)
5 sec.
Disarmed (yellow)
Acoustic 1 sec.
(signal)
Acknowledegement
Time-controlled
Action
door release

10.3 Arming/disarming an IDS

Reader with keypad
- Hold data carrier in the reading range (and/or enter PIN).
Green LED lights up
Yellow LED lights up when disarmed and remains dark when armed.
- Strike the corresponding key (arming "E" or disarming "C").
- Acknowledgement (according to tables below).
Reader without keypad
- Hold data carrier in the reading range and remove.
Green LED lights up
Yellow LED lights up when disarmed and remains dark when armed.
- Hold data carrier again in the reading range after 1 to max 4 seconds.
- Acknowledgement (according to tables below).
Acknowledgement when arming:
Optical Fulfilled with authorisation
and positive drive
Ready
5 sec.
(green)
Disarmed
disarmed armed
(yellow)
Alarm
(red)
Acoustic
1 sec.
(signal)
Acknowledgement
Action System will be
armed
Acknowledgement when disarming:
Optical Fulfilled with authorisation
and positive drive
Ready
5 sec.
(green)
Disarmed
armed disarmed
(yellow)
Alarm
Lights up in case
(red)
of alarm
Acoustic
1 sec.
(signal)
Acknowledgement
Action System will be
disarmed
10.4 AC function after disarming
Depending on the system programming, there are
function after disarming:
1. To open the door, hold the ID data carrier
or
2. AC function will automatically be active after disarming.
No authorisation or
AC function not activated
1 sec.
Acknowledegement
No door release
(only via IK3 EU)
With authorisation but No authorisation
no positive drive
5 sec.
5 sec.
Lights up in case
of alarm
1 sec. 1 sec.
Acknowledgement Acknowledgement
System will not be System will
armed armed
With authorisation but No authorisation
no positive drive
5 sec.
5 sec.
Lights up in case
of alarm
1 sec. 1 sec.
Acknowledgement Acknowledgement
System will not be System will
disarmed disarmed
two possibilities to activate the AC
one more time in the reading range.
Mounting and Operating Instructions Reader series Insertic
10.5 Learning mode for data carriers
In learning mode it is simple to authorize new data carriers or delete existing ones.
Newly "learned" data carriers automatically receive
version V09 (MB24/48/100) and version V03 (MB256 plus), the PINs / authorizations /
time zones must be assigned afterwards via the programming functions .
To start the learning mode, you need a
exclusively for this purpose in the system. However, the learning key has no
authorizations.
As long as learning mode is activated, you can enter or delete as many data carriers as
you want one after another.
LED indication:
green yellow red
Buzzer signals:
- Buzzer sound single:
The performed action was successful, learning
mode activated or data carrier learned.
- Buzzer sound twice:
Data carrier erased.
- Buzzer sound triple:
Invalid action. An invalid action is given if a
programmed data carrier is to be learned or an
unprogrammed data carrier is to be erased.
!
Reader with keypad
Start learning mode
L
Learn data carrier
ID
Delete data carrier
ID
not be
Exit learning mode
L L
!
Reader without keypad
Start learning mode
L
not be
Learn data carrier
ID
Exit learning mode
L
general authorization
"learning key" . This is a data carrier set up
The "Ready" LED (green) and the "Disarmed" LED (yellow)
serve as a visual acknowledgement signal in learning mode.
Hold the learning key in the reading field until buzzer signal
LEDs green and yellow light up
Press the "I" button , short buzzer signal
LEDs green and yellow start flashing,
the learning mode is activated
Hold the new data carrier in the reading field until buzzer signal
LED green is on, LED yellow flashes
Press the "I" button, short buzzer signal
LEDs green and yellow are flashing
Hold the old data carrier in the reading field until buzzer signal
LED green is on, LED yellow flashes
Press the "O" button, 2 short buzzer signals
LEDs green and yellow flashing
Hold the learning key in the reading field until buzzer
C
signal, then press the "O"
or
Exits automatically approx. 60 seconds after the last operation
LEDs green and yellow off
Hold the learning key in the reading field until buzzer signal
LEDs green and yellow light up
LEDs green and yellow start flashing,
the learning mode is activated
Hold the new data carrier in the reading field until buzzer signal
LED green is on, LED yellow flashes
short buzzer signal
LEDs green and yellow flashing
Hold the learn master key in the reading range until buzzer signal
or
Exits automatically approx. 60 seconds after the last operation
LEDs green and yellow off
, as of
Buzzer sound single
Buzzer sound twice
Buzzer sound triple
green yellow red
button