EMAG Emmi-04D Bedienungsanleitung Seite 12

4. USER MANUAL
Emmi 05P
Fill tank with tap water. (about ¾ of the tank volume should be filled with water which is approx. 1 cm
below the upper tank rim) Plug the power cord into the power socket. For a thorough cleaning of your
items, we recommend certain cleaning additives (see Section 5. Cleaning additives). For the cleaning of
eyeglasses and dental prosthesis please use the basket supplied (2). By pushing the ON switch (1) the
cleaning operation can be started. Each successive push will increase the cleaning time by 1 minute
(maximum 9 minutes). The cleaning time to be set depends on the degree of contamination of the
objects to be cleaned. When the set cleaning time has expired, the digital time display will show „0" and
the unit will stop the cleaning process automatically. If you wish to stop the equipment earlier please
push the OFF switch. The tub is portable and makes it easier to fill and empty the tub with water. After
the completion of the cleaning process, remove the cleaned items from the tub and rinse briefly under
running water to remove any remaining dirt particles. After the completion of the cleaning process (or
several cleaning processes) it is recommended to remove the water from the tub, rinse the tub briefly
and wipe dry with a cloth. Please make sure that no water enters the housing through the ventilation
slots in the bottom of the unit.
Note:
Please take into account a degassing time when filling fresh water depending on the degree of
hardness. In order to degas the water, we recommend that the device be run with filled water for a few
minutes before putting the objects in.
Emmi 04D
Fill tank with tap water to just below the MAX mark. Plug the power cord into the power socket. For
thorough and optimal cleaning of the items, we recommend the use of the respective EMAG cleaning
concentrates (see sect. 5 cleaning accessories). Place the contaminated objects in the plastic basket and
place them in the tub filled with water. To switch on the device, press the ON/OFF button, then use the
Timer to set the cleaning time required. Time needed depends on the degree of contamination of the
objects. (Adjustment times 1/3/5/7/9 Minutes) After the desired cleaning time has elapsed, remove the
cleaned material with the basket from the tub and rinse under running water. The device will now show
the "0" position. If you are done with the unit, unplug the power cord. The STANDBY indicator light, by
function, goes out when the unit is switched off. If the unit is not to be used for an extended period of
time, it is recommended to empty the tub and dry it with a cloth.
Emmi D21
Fill the tub with tap water between the marking ranges MIN±MAX. It should be noted that the cleaning
objects must be completely covered with water. Plug the power cord into the power socket. For
thorough and optimal cleaning of the items, we recommend the use of the respective EMAG cleaning
concentrates (see sect. 5 cleaning accessories). Place the contaminated objects in the plastic basket and
place them in the tub filled with water (See note below). To switch on the device, press the START/STOP
button, then adjust the cleaning time (5-10-15 Min.). Then the operating lamp lights up on the Display. If
the heating is to be switched on, press the heating control button. The water then heats up and switches
off automatically when the maximum temperature of 60°C is reached. For safety, due to overheating, the
heater switches off automatically after 45 minutes of starting. Should overheating occur, the overheating
lamp will light up red and you should unplug the power cord to turn off the unit. After completion of the
cleaning process, remove the cleaned item(s) from the tub and rinse briefly under running water. If the
unit is no longer to be used, unplug the power cord and the STANDBY indicator will turn off automati-
cally. If the unit is not to be used for an extended period of time, it is recommended to empty the tub
and dry it with a cloth.
Emmi 04D
Fill tank with tap water to just below the groove. Plug the power cord into the power socket. For
thorough and optimal cleaning of the items, we recommend the use of the respective EMAG cleaning
concentrates (see sect. 5 cleaning accessories). Place the contaminated objects in the basket and place
them in the tub filled with water. To switch on the device, press the ON/OFF button, then use the Timer
12
Onlineshop: ultraschall-welt.de