Warranty Provisions - Niko 350-70980 Handbuch

350-70980
Read the complete user manual before carrying out the installation and activating the system. Keep
the manual for future reference.
1. DESCRIPTION
This relay module is connected directly to the DALI bus and can be used to make an extra connection. You should
only use this module when the internal relay is already occupied or, for instance, when you need two on/off zones.
2. MOUNTING
The relay module must always be mounted in a closed box (e.g. in a connection box).
Only connect the module to the power supply once all wires have been connected in accordance with the wiring
diagram (see Fig. 1). The red LED will light up when the relay module is activated (see Fig. 2).
Lock/ Lock/ Lock/ Lock/ Test Test Test Test
Init. Init. Init. Init. Next Next Next Next
unlock unlock unlock unlock On/Off On/Off On/Off On/Off
3. SETTINGS
100 lx/ 100 lx/ 100 lx/ 100 lx/ 200 lx/ 200 lx/ 200 lx/ 200 lx/ 300 lx/ 300 lx/ 300 lx/ 300 lx/ 400 lx/ 400 lx/ 400 lx/ 400 lx/
5 min 5 min 5 min 5 min 10 min 10 min 10 min 10 min 15 min 15 min 15 min 15 min 30 min 30 min 30 min 30 min
The relay module is not programmed separately. Like a luminaire, it is addressed during the configuration of the
(master) detector that controls the DALI bus. To do so, you must use the installer IR remote control 350-41934.
600 lx/ 600 lx/ 600 lx/ 600 lx/ 800 lx/ 800 lx/ 800 lx/ 800 lx/ 1000 lx/ 1000 lx/ 1000 lx/ 1000 lx/
∞ ∞ ∞ ∞
45 min 45 min 45 min 45 min 60 min 60 min 60 min 60 min
min min min
At the moment you address the relay module, you can choose between three different modes:
Lock/
1. Switching an extra light circuit on or off Init.
Fact. Fact. Fact. Fact.
unlock
Mode Mode Mode Mode
Time Time Time Time Lux Lux Lux Lux
set. set. set. set.
2. Switching HVAC on or off
3. Cut-off
100 lx/ 200 lx/
5 min 2/3 10 min 2/3 2/3
RF RF RF RF
Status Status Status Status
Burn in Burn in Burn in Burn in
zone zone zone zone
3.1. Switching an extra light circuit on or off
600 lx/ 800 lx/
45 min Min./ Min./ Min./ 60 min Min./
Sens. Sens. Sens. Sens. Calib. Calib. Calib. Calib.
8 hour 8 hour 8 hour 8 hour
Off Off Off
Use this mode when you connect an extra light circuit to the relay module.
Lock/
Test
Init. Next
unlock On/Off
Lock/ Test
Init. Next
Time Lux
unlock 1 1 1 1 On/Off 2 2 2 2 0,5 s 3 3 3 3 4 s 4 4 4
Press / / /
to the extra light circuit.
100 lx/ 200 lx/ 300 lx/ 400 lx/
5 min 10 min 15 min 30 min
100 lx/ 200 lx/ 300 lx/ 400 lx/
Status
Burn in
5 min 10 min 15 min 30 min
On/Off On/Off On/Off On/Off Auto Auto Auto Auto Dim - Dim - Dim - Dim - Dim + Dim + Dim + Dim +
3.2. Switching HVAC on or off
600 lx/ 800 lx/ 1000 lx/
∞
45 min 60 min
600 lx/ 800 lx/ 1000 lx/ min
Sens.
8 hour
45 min 60 min ∞
min
Use this mode when you connect an HVAC system to the relay module.
Fact.
Lock/ Test
Mode
Next Time Lux
Init.
unlock On/Off 0,5 s 4 s set.
Fact.
Mode 1 2
Time Press Lux and then on the remote control to select this mode.
set.
100 lx/ 200 lx/ 300 lx/ 400 lx/ 2/3
RF
Status
Burn in
3.3. Cut-off
zone
5 min 10 min 15 min 30 min 2/3
RF
Status
Burn in On/Off Auto
zone
Use this mode when you want to use the relay module as a cut-off (e.g. as an extra safety measure when using
600 lx/ 800 lx/ 1000 lx/ Min./
Sens. Calib.
8 hour
45 min 60 min ∞ Off
Min./ min
Sens. Calib.
8 hour
luminaires with a different phase).
Off
1 2 3 4
Fact.
Mode
Time Press Lux and then on the remote control to select this mode.
set.
1 2 3 4
4. TECHNICAL DATA
2/3
RF
Status On/Off Auto Dim - Dim +
Burn in
zone
Auto Dim - Dim +
On/Off
Reference code
Min./
Sens. Calib.
8 hour
Off
Power supply voltage
1 2 3 4
Power consumption
DALI input
Auto Dim - Dim +
On/Off
Relay output
Maximum switching capacity
Maximum inrush current
Maximum incandescent lamp load
Maximum halogen lamp load
Maximum fluorescent lamp load
Maximum fluorescent lamp load with HF ballast
Maximum halogen transformer load
Maximum electronic LED driver load
Maximum load for 230 Vac LED lamps
Maximum load for economy lamps (CFLi)
Protection degree
Colour (housing)
Ambient temperature
Marking
DALI standards
5. WARNINGS REGARDING INSTALLATION
• The installation should be carried out by a registered installer and in compliance with the applicable regulations.
• This user manual should be presented to the user. It should be included in the electrical installation file, and
it should be passed on to any new owners. Additional copies are available on the Niko website or via the Niko
support service. The latest manual for this product is available on the Niko website at any time.
• During installation, the following should be taken into account (non-exhaustive list):
- the applicable laws, standards and regulations.
- the technology available at the time of installation.
- this user manual, which only states general regulations and should therefore be read within the scope
4
of each specific installation.
- the rules of proper workmanship.
This product complies with all of the relevant European guidelines and regulations. If applicable, you can find
the EC declaration of conformity regarding this product at www.niko.eu.
6. NIKO SUPPORT
EN
0,5 s 0,5 s 0,5 s 0,5 s 4 s 4 s 4 s 4 s
min
Test
Next
On/Off 0,5 s 4 s
300 lx/ 400 lx/
2/3 15 min 30 min
1000 lx/
∞
min
Off
0,5 s 4 s
Fact.
Mode
4
set.
on the remote control to indicate which zone should be connected
2/3
RF
zone
Min./
Calib.
Off
3 4
Dim - Dim +
350-70980
230 Vac ±10 %, 50 Hz
0.2 W
2.3 mA
µ 6 A, 250/400 Vac, N.O.
140 uF
165 A/20 m sec.
800 A/200 μ sec.
1380 W
1380 W
720 VA
720 VA
300 VA
300 VA
150 W
34 pieces (18 W)
IP 20
Grey
-5 °C – +40 °C
CE marked
EN 62386-101
EN 62386-102
EN 62386-208
nv Niko sa Industriepark West 40, BE-9100 Sint-Niklaas, Belgium — tel. +32 3 778 90 00 — fax +32 3 777 71 20 — e-mail: support@niko.be — www.niko.eu
In case of doubt or if you want to exchange the product in case of a defect, contact your wholesaler or the
Niko support service:
• Belgium: +32 3 778 90 80
• The Netherlands: +31 880 15 96 10
Contact details and more information can be found at www.niko.eu under the 'Help and advice' section.

7. WARRANTY PROVISIONS

• The period of guarantee is four years from the date of delivery. The delivery date is the invoice date of purchase
of the product by the consumer. If there is no invoice, the date of production applies.
• The consumer is obliged to inform Niko in writing about the non-conformity, within two months of noticing
the defect.
• In case of a non-conformity, the consumer only has the right to a product repair or replacement free of charge,
which shall be decided by Niko.
• Niko shall not be held liable for a defect or damage resulting from incorrect installation, improper or careless
use, incorrect operation, transformation of the product, maintenance that does not adhere to the maintenance
instructions or an external cause, such as damage due to moisture or overvoltage.
• The compulsory regulations of the national legislation concerning the sale of consumer goods and the
protection of the consumer in the countries where Niko sells, directly or via sister companies, subsidiaries,
chain stores, distributors, agents or permanent sales representatives, take priority over the above-mentioned
rules and regulations.
This product cannot be deposited in the unsorted waste. Take your discarded product to a recycling centre or a recognised
collection point. Just like producers and importers, you too play an important role in the promotion of sorting, recycling and
reuse of waste electrical and electronic equipment. To finance the rubbish collection and waste treatment, the government
levies recycling charges in certain cases (included in the price of this product).
PM350-70980R16253