Drainage System; Hydraulic Connections; Electrical Connections; Audio System - Jacuzzi Sasha Vorinstallationsblatt

Drainage system

Two drainage pipes are provided.
- We recommend connecting the two drainage pipes so that you
are left with one drainage outlet, as indicated in positions 1 or 1a.
It is also possible to independently connect the drainage pipes
to the drainage system.
In all cases, you must ensure that the drainage pipe fittings are
routed to the floor, as indicated, whilst bearing in mind the posi-
tioning of the frame supports (feet).

Hydraulic connections

For connection to the water supply (position 5D - shower) we
advise using pipes with min Ø 14 mm; these pipes must have a
1/2" M pipe joint.
If the "sauna" model is equipped with an automatic filling tank
a 1/2" M (cold water) fitting must be provided (position 5S).
In order to ensure correct operation, the pressure and flow
rate values must also comply with the values specified in the rel-
evant "Hydraulic specifications".
Where "hard" water is present, it is advisable to install
a decalcifier in the water system supplying water to the
appliance, in order to reduce and/or avoid calcareous
deposits.
ATTENTION: (IEC 60335-1/A2) The pressure of the wa-
ter system supplying water to the appliance must not
exceed 600 k Pa (6 bar).

Electrical connections

The electrical connection can be made in one of the following ways:
sauna
- single-phase line (220-240V 1~);
- three-phase line consisting of three phase conductors +
neutral conductor (380-415V 3N~).
shower
- single-phase line (220-240V 1~);
The rated power supply voltage of the equipment is
always 220-240V.
The equipment can also be installed in countries where
the 220-240V voltage is supplied by a two-phase system. For
the connection please refer to the instruction manual.
Each "sauna" is supplied with an isolating multi-pole switch,
complete with a cable, approximately 400 cm in length, already con-
nected to the appliance's junction box, as indicated in position 2S.
This switch must be connected to an area that complies with the
safety regulations as specified by current legislation in force.
Each "shower" is supplied with a terminal block located in
the equipment zone a cable must be connected to this termi-
nal block (position 2D); the aforementioned cable must be con-
nected to an isolating multi-pole switch;this switch must be con-
nected to an area that complies with the safety regulations as
specified by current legislation in force.
For guidance with regards to electrical connections,
please refer to the installation manual.
Some models allow you to connect the appliance to an alarm
circuit (provided, in the area marked with the bell symbol), a
bipolar cable with characteristics not inferior to type H 05 VV-F
2x2.5 mm 2 (220-240V - 2A max.); this cable must be used in order
to ensure that the cable clamp attached to the box offers ad-
equate protection (water tight) as detailed by legislation.

Audio system

"Sauna" and/or "hammam" are equipped with speakers* that
can be connected to a cable radio system circuit; the relevant ca-
ble must be arranged as indicated in position 3.
Upon request, an audio kit is available, which can be installed in
the appliance's appropriate equipment zone, to which the speak-
ers will also be connected.
NOTE:
(*) two speakers; impedance: 4 Ω - optimal power: 20 W x2.
Remote control system arrangement
(where present)
It is possible to manage the "sauna" and "hammam" functions
using a computer which interfaces with a remote control system
(sc) via an Ethernet (LAN) network:
sc
it is also possible yo use a smartphone or tablet computer,
which interfaces via a wireless network (WLAN/Wi-Fi):
sc
sim
In any case, you must use an Ethernet socket (RJ-45), as indicated
in position 8, to which the cable (length: ~ 5 m) coming from the
remote control system, must be connected.
19
LAN
SMS
wi-fi