4.4.5 Kabelanschluss Schirmung und Kabelverlegung Inbetriebnahme System in Betrieb nehmen Hinweise zum Betrieb SSI-Schnittstelle Prinzip Datenformate Fehlerhafte SSI-Abfrage Synchroner und asynchroner Betrieb Konfiguration mit dem BTL7 Configuration Tool (nur für BTL7-S510(B)-…) BTL7 Configuration Tool Anschluss der USB-Kommunikationsbox Konfigurationsmöglichkeiten www.balluff.com deutsch...
Normen sind in der Konformitätser- Bauformen lieferbar und deshalb gesondert zu klärung aufgeführt. bestellen. Verwendete Abkürzungen Zulassungen und Kennzeichnungen Synchron-Serielle Schnittstelle (Synchronous Serial Interface) Nicht bei BTL7-…-FA_ _ US-Patent 5 923 164 Das US-Patent wurde in Verbindung mit diesem Produkt erteilt. www.balluff.com deutsch...
Industriebereich vorgesehen. Die einwandfreie Funktion Die verwendeten Warnhinweise enthalten verschiedene gemäß den Angaben in den technischen Daten wird nur Signalwörter und sind nach folgendem Schema aufgebaut: mit original Balluff Zubehör zugesichert, die Verwendung SIGNALWORT anderer Komponenten bewirkt Haftungsausschluss. Art und Quelle der Gefahr Das Öffnen des BTL oder eine nichtbestimmungsgemäße...
Funktionen gewählt werden (nur – Ø 10,2 mm: Nennlänge von 25 mm bis 7620 mm BTL7-S510…): – Ø 8 mm: Nennlänge von 25 mm bis 1016 mm – Positionsdifferenz – Geschwindigkeit (mit oder ohne Vorzeichen) Dämpfungszone: Messtechnisch nicht nutzbarer Bereich – Geschwindigkeitsdifferenz am Stabende, der überfahren werden darf. www.balluff.com deutsch...
BTL7-S5 _ _ ( _ )-M _ _ _ _ -A/B/Y/Z(8)-S32/S115/S140/S147/KA _ _ /FA _ _ Magnetostriktives Positionsmesssystem — Bauform Stab Aufbau und Funktion (Fortsetzung) Verhalten der LED 1 und des Fehlerwerts über den gesam- LED-Anzeige ten Bereich: LED 1 LED 2 Magnet fehlt ≈ 5 mm Nullpunkt Endpunkt Bild 3-2: Lage der LED-Anzeigen BTL7 Bild 3-3:...
Bild 4-4: Einschraubloch 3/4"-16UNF nach SAE J475 Stabdurchmesser Bohrungsdurchmesser D2 O-Ring 15.3x2.4 10,2 mm mindestens 13 mm Positionsgeber: Für das BTL stehen unterschiedliche 8 mm mindestens 11 mm Positionsgeber zur Verfügung (siehe Zubehör auf Tab. 4-1: Bohrungsdurchmesser bei Einbau in einen Seite 21). Hydraulikzylinder www.balluff.com deutsch...
Tab. 4-2: Anschlussbelegung BTL7…-S32 werden, aber nicht mit dem Schirm. Kommunikationsleitung Tab. 4-4: Anschlussbelegung BTL7…-S140 Bild 4-9: Pinbelegung S32 (Draufsicht auf Stecker am BTL), 8-poliger Rundstecker M16 Bild 4-11: Pinbelegung S140 (Draufsicht auf Stecker am BTL), 10-poliger Rundstecker www.balluff.com deutsch...
Reparatur durch den Hersteller die korrekten Werte im Nullpunkt und Endpunkt prüfen. Hinweise zum Betrieb – Funktion des BTL und aller damit verbundenen Kom- ponenten regelmäßig überprüfen. – Bei Funktionsstörungen das BTL außer Betrieb neh- men. – Anlage gegen unbefugte Benutzung sichern. www.balluff.com deutsch...
BTL7-S5 _ _ ( _ )-M _ _ _ _ -A/B/Y/Z(8)-S32/S115/S140/S147/KA _ _ /FA _ _ Magnetostriktives Positionsmesssystem — Bauform Stab SSI-Schnittstelle Prinzip Beim BTL7-S5_ _B/F-M… werden die Positionsdaten synchron zur externen Abtastperiode zeitnah ermittelt und SSI bedeutet Synchronous Serial Interface und beschreibt ausgegeben. Für einen synchronen Betrieb muss die eine digitale synchrone Schnittstelle mit einer differenziellen Abtastperiode T im Bereich T...
-Event T Ablauf der korrekten Anzahl von Takten auf Low. Mit jeder weiteren negativen Flanke von Clk wird der t -Timer erneut gestartet und intern der T -Event gesetzt. Nach Ablauf der Zeit t geht Data wieder auf High. www.balluff.com deutsch...
BTL7-S5 _ _ ( _ )-M _ _ _ _ -A/B/Y/Z(8)-S32/S115/S140/S147/KA _ _ /FA _ _ Magnetostriktives Positionsmesssystem — Bauform Stab SSI-Schnittstelle (Fortsetzung) Synchroner und asynchroner Betrieb Im synchronen Betrieb müssen zwei Randbedingungen beachtet werden: Synchroner Betrieb – Die externe Abtastfrequenz f muss sich im Bereich Für regeltechnische Anwendungen ist häufig ein gleichmä- 62,5 Hz < f < f...
Eine Bewegung vom Anfangspunkt zum Endpunkt wird Die PC-Software und das zugehörige Hand- mit positivem Vorzeichen ausgegeben, eine Bewegung buch erhalten Sie im Internet unter vom Endpunkt zum Anfangspunkt mit negativem www.balluff.com. Vorzeichen. – Geschwindigkeit (kein Vorzeichen): Geschwindig- keit des Positionsgebers, die Bewegungsrichtung kann nicht abgelesen werden.
0,1 mm/s Für UL: Gebrauch in geschlossenen Räumen und bis zu einer Höhe von min. erfassbare Geschwindigkeit 1 mm/s 2000 m über Meeresspiegel. Einzelbestimmung nach Balluff Werknorm max. erfassbare Geschwindigkeit 10 m/s Resonanzfrequenzen ausgenommen Für UL: Das BTL muss extern über einen energiebegrenzten Stromkreis Umgebungsbedingungen gemäß...
Durchmesser Stab 8 mm oder 10,2 mm Nennlänge bei Ø 8 mm 25…1016 mm bei Ø 10,2 mm 25…7620 mm Gewicht (längenabhängig) ca. 2 kg/m Gehäusematerial Aluminium Flanschmaterial Edelstahl Stabmaterial Edelstahl Wandstärke Stab bei Ø 8 mm 0,9 mm bei Ø 10,2 mm 2 mm Gehäusebefestigung über M18×1.5 oder 3/4"-16UNF Gewinde Anzugsdrehmoment max. 100 Nm www.balluff.com deutsch...
BTL7-S5 _ _ ( _ )-M _ _ _ _ -A/B/Y/Z(8)-S32/S115/S140/S147/KA _ _ /FA _ _ Magnetostriktives Positionsmesssystem — Bauform Stab Technische Daten (Fortsetzung) Verbindung zur Auswerteeinheit Die maximale Abtastfrequenz f , bei der mit jeder Abtas- Die minimale Abtastfrequenz f beträgt 62,5 Hz. A,max A,min tung ein neuer aktueller Wert ansteht, lässt sich aus der folgenden Grafik entnehmen: in Hz...
Seite 31
Startup Starting up the system Operating notes SSI interface Principle Data formats Faulty SSI query Synchronous and asynchronous operation Configuration with the BTL7 Configuration Tool (only for BTL7-S510(B)-…) BTL7 Configuration Tool Connecting the USB communication box Configuration options www.balluff.com english...
Seite 32
BTL7-S5 _ _ ( _ )-M _ _ _ _ -A/B/Y/Z(8)-S32/S115/S140/S147/KA _ _ /FA _ _ Magnetostrictive Linear Position Sensor — Rod Style Technical data Accuracy Ambient conditions Supply voltage Communication lines La, Lb Output Dimensions, weights Connection to the evaluation unit Accessories Magnets Mounting nut Connector type S32 9.3.1 Freely configurable 9.3.2 Preassembled...
Approvals and markings Abbreviations Synchronous Serial Interface Not for BTL7-…-FA_ _ US Patent 5 923 164 The US patent was awarded in connection with this product. www.balluff.com english...
Flawless function in accordance with the specifications in are structured as follows: the technical data is ensured only when using original SIGNAL WORD Balluff accessories. Use of any other components will void the warranty. Hazard type and source Consequences if not complied with...
Ø 8 mm: Nominal length from 25 mm to 1016 mm – Differential position – Speed (with or without leading sign) Damping zone: Area at the end of the rod that cannot be – Speed difference used for measurements, but which may be passed over. www.balluff.com english...
BTL7-S5 _ _ ( _ )-M _ _ _ _ -A/B/Y/Z(8)-S32/S115/S140/S147/KA _ _ /FA _ _ Magnetostrictive Linear Position Sensor — Rod Style Construction and function (continued) Behavior of LED 1 and the error value through the entire LED display range: LED 1 LED 2 Magnet missing ≈ 5 mm Null point End point Fig.
Fig. 4-4: Mounting hole 3/4"-16UNF per SAE J475 O-ring 15.3x2.4 Rod diameter Bore diameter D2 Magnet: Various magnets are available for the BTL (see 10.2 mm At least 13 mm Accessories on page 21). 8 mm At least 11 mm Tab. 4-1: Bore diameter if installed in a hydraulic cylinder www.balluff.com english...
BTL7-S5 _ _ ( _ )-M _ _ _ _ -A/B/Y/Z(8)-S32/S115/S140/S147/KA _ _ /FA _ _ Magnetostrictive Linear Position Sensor — Rod Style Installation and connection (continued) The sliding element can be screwed on or bonded. Installing the BTL ► Secure the screws so they cannot be loosened or lost. ►...
Communication line Tab. 4-4: Connection assignment BTL7…-S140 Fig. 4-9: Pin assignment of S32 (view of connector pins of BTL), 8-pin M16 circular plug Fig. 4-11: Pin assignment of S140 (view of connector pins of BTL), 10-pin circular plug www.balluff.com english...
BTL or after repair by the manufacturer. Operating notes – Check the function of the BTL and all associated components on a regular basis. – Take the BTL out of operation whenever there is a malfunction. – Secure the system against unauthorized use. www.balluff.com english...
BTL7-S5 _ _ ( _ )-M _ _ _ _ -A/B/Y/Z(8)-S32/S115/S140/S147/KA _ _ /FA _ _ Magnetostrictive Linear Position Sensor — Rod Style SSI interface Principle With the BTL7-S5_ _B/F-M…, position data is determined and output in a timely manner and synchronous to the SSI stands for Synchronous Serial Interface and describes external sampling period.
The t timer is started again for every additional negative edge from Clk and the T event is set internally. Data switches back to high after the time t elapsed. www.balluff.com english...
BTL7-S5 _ _ ( _ )-M _ _ _ _ -A/B/Y/Z(8)-S32/S115/S140/S147/KA _ _ /FA _ _ Magnetostrictive Linear Position Sensor — Rod Style SSI interface (continued) Synchronous and asynchronous operation Two boundary conditions must be taken into account during synchronous operation: Synchronous operation – The external sampling frequency f must be in the range A uniform and brief timing is often required for control 62.5 Hz < f...
Internet under movement from the end point to the starting point is www.balluff.com. output with a negative sign. – Speed (unsigned): Speed of the magnet, the direction of movement cannot be read.
1 mm/s level. Max. detectable speed 10 m/s Individual specifications as per Balluff factory standard Resonant frequencies excluded Ambient conditions For UL: The BTL must be externally connected via a limited-energy circuit as defined in UL 61010-1, a low-power source as defined in UL 60950-1, Ambient temperature −40…+85°C...
For Ø 10.2 mm 25…7620 mm Weight (depends on Approx. 2 kg/m length) Housing material Aluminum Flange material Stainless steel Rod material Stainless steel Rod wall thickness For Ø 8 mm 0.9 mm For Ø 10.2 mm 2 mm Housing mounting via M18×1.5 or 3/4"-16UNF threads Tightening torque Max. 100 Nm www.balluff.com english...
BTL7-S5 _ _ ( _ )-M _ _ _ _ -A/B/Y/Z(8)-S32/S115/S140/S147/KA _ _ /FA _ _ Magnetostrictive Linear Position Sensor — Rod Style Technical data (continued) Connection to the evaluation unit The maximum sampling frequency f , at which a new The minimum sampling frequency f is 62,5 Hz.
BKS-S116-PU-05 (Order code: BCC00YW): Cable length 5 m M12x1 Fig. 9-7: Connector BKS-S116-PU-_ _ Fig. 9-8: Connector BKS-S116-PU-_ _, outlet Color YE yellow GY gray PK pink RD red GN green BU blue BN brown WH white Tab. 9-2: BKS-S115/S116-PU-_ _ pin assignment www.balluff.com english...
BTL7-S5 _ _ ( _ )-M _ _ _ _ -A/B/Y/Z(8)-S32/S115/S140/S147/KA _ _ /FA _ _ Magnetostrictive Linear Position Sensor — Rod Style Type code BTL7 standard BTL7 - S 5 0 1 B - M0500 - B - S32 SSI interface Supply voltage: 5 = 10…30 V DC Data format: 24 bit 25 bit...
Seite 53
Y8 = 3/4"-16UNF thread, for flat seal, rod diameter 8 mm Z8 = 3/4"-16UNF thread, O-ring, rod diameter 8 mm Electrical connection: S32 = 8-pin, M16 plug per IEC 130-9 S115 = 8-pin, M12 plug S140 = 10-pin, plug KA05 = Cable, 5 m (PUR) FA05 = Cable, 5 m (PTFE) www.balluff.com english...
BTL7-S5 _ _ ( _ )-M _ _ _ _ -A/B/Y/Z(8)-S32/S115/S140/S147/KA _ _ /FA _ _ Magnetostrictive Linear Position Sensor — Rod Style Appendix 11.1 Converting units of length 11.2 Product labels 1 mm = 0.0393700787 inch inches 0.03937008 0.07874016 0.11811024 0.15748031 0.19685039 0.23622047 0.27559055 0.31496063 0.35433071 0.393700787 Tab. 11-1: Conversion table mm to inches Order code 1 inch = 25.4 mm Type code...
Seite 57
Mise en service du système Conseils d’utilisation Interface SSI Principe Formats de données Interrogation SSI erronée Fonctionnements synchrone et asynchrone Configuration avec BTL7 Configuration Tool (uniquement pour BTL7-S510(B)-...) 17 BTL7 Configuration Tool Raccordement du module de communication USB Possibilités de configuration www.balluff.com français...
Seite 58
BTL7-S5 _ _ ( _ )-M _ _ _ _ -A/B/Y/Z(8)-S32/S115/S140/S147/KA _ _ /FA _ _ Système de mesure de position magnétostrictif — Forme à tige Caractéristiques techniques Précision Conditions ambiantes Alimentation électrique Câbles de communication La et Lb Sorties Dimensions, poids Connexion à l’unité d’analyse Accessoires Capteurs de position Ecrou de fixation...
Homologations et certifications homologations et certifications, se reporter à la déclaration de conformité. Abréviations utilisées Interface série synchrone (Synchronous Serial Sauf pour BTL7-...-FA_ _ Interface) Brevet US 5 923 164 Le brevet américain a été attribué en relation avec ce produit. www.balluff.com français...
MOT-CLE figurant dans les caractéristiques techniques, n’est garanti qu’avec les accessoires d’origine de Balluff, l’utilisation Type et source de danger d’autres composants entraîne la nullité de la garantie. Conséquences en cas de non-respect du danger Tout démontage du BTL ainsi que toute utilisation non...
Zone d’amortissement : plage non utilisable à des fins suivantes (uniquement pour BTL7-S510...) : de mesure, située à l’extrémité de la tige, où le capteur – Différence de position peut toutefois pénétrer. – Vélocité (avec ou sans signe) – Différence de vélocité www.balluff.com français...
BTL7-S5 _ _ ( _ )-M _ _ _ _ -A/B/Y/Z(8)-S32/S115/S140/S147/KA _ _ /FA _ _ Système de mesure de position magnétostrictif — Forme à tige Structure et fonction (suite) Comportement de la LED 1 et de la valeur d’erreur pour Affichage à LED l’ensemble de la plage : LED 1 LED 2 Aimant...
10,2 mm minimum 13 mm joint torique 15.3x2.4 8 mm minimum 11 mm Capteur de position : différents capteurs de position sont Tab. 4-1: Diamètre de perçage en cas de montage dans un vérin disponibles pour le BTL (voir Accessoires, page 21). hydraulique www.balluff.com français...
BTL7-S5 _ _ ( _ )-M _ _ _ _ -A/B/Y/Z(8)-S32/S115/S140/S147/KA _ _ /FA _ _ Système de mesure de position magnétostrictif — Forme à tige Montage et raccordement (suite) L’élément coulissant peut être vissé ou collé. Montage du BTL ► Sécuriser les vis contre le desserrage ou la perte. ►...
Affectation des broches BTL7...-S140 Fig. 4-11: Brochage du connecteur S140 (vue de dessus sur le Fig. 4-9: Brochage du connecteur S32 (vue de dessus sur le connecteur du BTL), connecteur rond à 8 pôles M16 connecteur du BTL), connecteur rond à 10 pôles www.balluff.com français...
BTL7-S5 _ _ ( _ )-M _ _ _ _ -A/B/Y/Z(8)-S32/S115/S140/S147/KA _ _ /FA _ _ Système de mesure de position magnétostrictif — Forme à tige Montage et raccordement (suite) 4.4.4 Connecteur S147 +Clk –Clk BTL7 Standard +Data –Data Broche BTL7-S5_ _...-S147 Analyse ou –Data BTL7…- +24 V commande câble...
BTL ou réparation par le fabricant. Conseils d’utilisation – Contrôler régulièrement le fonctionnement du BTL et de tous les composants associés. – En cas de dysfonctionnement, mettre le BTL hors service. – Protéger le système de toute utilisation non autorisée. www.balluff.com français...
BTL7-S5 _ _ ( _ )-M _ _ _ _ -A/B/Y/Z(8)-S32/S115/S140/S147/KA _ _ /FA _ _ Système de mesure de position magnétostrictif — Forme à tige Interface SSI Principe Pour le BTL7-S5_ _B/F-M…, les données de position sont déterminées et émises en temps réel et de manière SSI signifie Synchronous Serial Interface et décrit une synchronisée avec la période d’échantillonnage externe.
à Low après écoulement du nombre Evènement T correct de cadences. Le minuteur t redémarre à chaque cadence négative supplémentaire de Clk tandis qu’en interne, l’évènement T a lieu. Une fois la durée t écoulée, Data s’élève à nouveau à High. www.balluff.com français...
BTL7-S5 _ _ ( _ )-M _ _ _ _ -A/B/Y/Z(8)-S32/S115/S140/S147/KA _ _ /FA _ _ Système de mesure de position magnétostrictif — Forme à tige Interface SSI (suite) Fonctionnements synchrone et asynchrone Lors du fonctionnement synchrone, deux conditions secondaires doivent être remplies : Fonctionnement synchrone – La fréquence d’échantillonnage externe f doit être Pour les applications de régulation, un minutage court et...
à la sortie par un signe négatif. correspondant sont disponibles sur notre site – Vélocité (aucun signe) : vélocité du capteur de Internet www.balluff.com. position, il est impossible de déduire le sens de mouvement. – Différence de positions : distance entre deux Raccordement du module de communication capteurs de position.
1 mm/s au-dessus du niveau de la mer. Vitesse max. enregistrable 10 m/s Détermination individuelle selon la norme d’usine Balluff Exception faite des fréquences de résonance Conditions ambiantes Pour UL : le BTL doit être raccordé en externe via un circuit électrique à...
Matériau du boîtier Aluminium Matériau du bride Acier inoxydable Matériau de la tige Acier inoxydable Epaisseur de la paroi de la tige pour Ø 8 mm 0,9 mm pour Ø 10,2 mm 2 mm Fixation du boîtier par M18×1.5 ou 3/4"-16UNF filetage Couple de serrage Max. 100 Nm www.balluff.com français...
BTL7-S5 _ _ ( _ )-M _ _ _ _ -A/B/Y/Z(8)-S32/S115/S140/S147/KA _ _ /FA _ _ Système de mesure de position magnétostrictif — Forme à tige Caractéristiques techniques (suite) Connexion à l’unité d’analyse Le graphique suivant permet de déterminer la fréquence La fréquence d’échantillonnage minimale f s’élève à...
Cotes de montage des capteurs de position BTL-P-0814-GR-PAF BTL-P-1013-4R, BTL-P-1013-4S, BTL-P-1012-4R, BTL-P-1014-2R : Poids : < 15 g Boîtier : Aluminium Matériel livré avec les capteurs de position BTL-P-1013-4R, BTL-P-1013-4S, BTL-P-1012-4R : Bague d’écartement : 8 mm, polyoxyméthylène (POM) www.balluff.com français...
BTL7-S5 _ _ ( _ )-M _ _ _ _ -A/B/Y/Z(8)-S32/S115/S140/S147/KA _ _ /FA _ _ Système de mesure de position magnétostrictif — Forme à tige Code de type BTL7 Standard BTL7 - S 5 0 1 B - M0500 - B - S32 Interface SSI Tension d’alimentation : 5 = 10 …...
Seite 79
Z8 = Filetage au pouce 3/4"-16UNF, joint torique, diamètre de tige 8 mm Raccordement électrique : S32 = 8 pôles, connecteur M16 selon IEC 130-9 S115 = 8 pôles, connecteur M12 S140 = 10 pôles, connecteur KA05 = Câble 5 m (PUR) FA05 = Câble 5 m (PTFE) www.balluff.com français...
Seite 83
Messa in funzione del sistema Avvertenze per il funzionamento Interfaccia SSI Principi Formato dati Interrogazione SSI errata Funzionamento sincrono ed asincrono Configurazione con il BTL7 Configuration Tool (solo per BTL7-S510(B)-...) BTL7 Configuration Tool Collegamento della scatola di comunicazione USB Possibilità di configurazione www.balluff.com italiano...
Seite 84
BTL7-S5 _ _ ( _ )-M _ _ _ _ -A/B/Y/Z(8)-S32/S115/S140/S147/KA _ _ /FA _ _ Sensore di posizionamento lineare magnetostrittivo — versione a barra Dati tecnici Precisione Condizioni ambientali Tensione di alimentazione Linee di comunicazione La, Lb Uscita Dimensioni, pesi Collegamento con l’unità di valutazione Accessori Datori di posizione Dado di fissaggio...
Ulteriori informazioni in merito a direttive, autorizzazioni e norme sono indicate nella dichiarazione di conformità. Abbreviazioni utilizzate Non per BTL7-...-FA_ _ Interfaccia seriale sincronica (Synchronous Brevetto statunitense 5 923 164 Serial Interface) Il brevetto statunitense è stato rilasciato in relazione a questo prodotto. www.balluff.com italiano...
è destinato all’impiego in ambiente industriale. parole di segnalazione e sono realizzate secondo lo Il funzionamento corretto secondo le indicazioni dei dati schema seguente: tecnici è garantito soltanto con accessori originali Balluff, PAROLA DI SEGNALAZIONE l’uso di altri componenti comporta l’esclusione della responsabilità.
Ø 8 mm: lunghezza nominale da 25 mm a 1016 mm BTL7-S510...): – Variazione di posizione Zona di smorzamento: campo alla fine della barra non – Velocità (con o senza segni) utilizzabile a fini metrologici e che può essere oltrepassato. – Variazione di velocità www.balluff.com italiano...
BTL7-S5 _ _ ( _ )-M _ _ _ _ -A/B/Y/Z(8)-S32/S115/S140/S147/KA _ _ /FA _ _ Sensore di posizionamento lineare magnetostrittivo — versione a barra Struttura e funzione (continua) Comportamento del LED 1 e del valore di errore sull’intero Display LED campo: LED 1 LED 2 Manca il magnete ≈...
Fig. 4-4: Foro di avvitamento 3/4"-16UNF secondo SAE J475 10,2 mm almeno 13 mm O-ring 15.3x2.4 8 mm almeno 11 mm Datore di posizione: per il BTL sono disponibili vari tipi di datori di posizione (vedere Accessori a pagina 21). Tab. 4-1: Diametro del foro nel montaggio in un cilindro idraulico www.balluff.com italiano...
BTL7-S5 _ _ ( _ )-M _ _ _ _ -A/B/Y/Z(8)-S32/S115/S140/S147/KA _ _ /FA _ _ Sensore di posizionamento lineare magnetostrittivo — versione a barra Montaggio e collegamento (continua) L’elemento scorrevole può essere avvitato o incollato. Montaggio BTL ► Assicursi che le viti non si allentino o vadano perse. ►...
Linea di comunicazione Tab. 4-4: Piedinatura BTL7...-S140 Fig. 4-9: Piedinatura S32 (vista in pianta del connettore sul BTL), connettore circolare M16 a 8 poli Fig. 4-11: Piedinatura S140 (vista in pianta del connettore sul BTL), connettore circolare a 10 poli www.balluff.com italiano...
Avvertenze per il funzionamento – Controllare periodicamente il funzionamento del BTL e di tutti i componenti ad esso collegati. – In caso di anomalie di funzionamento disattivare il BTL. – Proteggere l’impianto da un uso non autorizzato. www.balluff.com italiano...
BTL7-S5 _ _ ( _ )-M _ _ _ _ -A/B/Y/Z(8)-S32/S115/S140/S147/KA _ _ /FA _ _ Sensore di posizionamento lineare magnetostrittivo — versione a barra Interfaccia SSI trasmessi sincronicamente al periodo di scansione esterno Principi ed emessi. Per un funzionamento sincrono il periodo di SSI è l’acronimo di Synchronous Serial Interface e descrive scansione T deve trovarsi nel campo T ≤ T...
In caso di troppi fronti di impulso l’output dati passa a Low breve al termine del numero corretto di impulsi. Per ogni fronte Evento T negativo ulteriore del Clk il timer t viene riavviato e l’evento viene impostato internamente. Alla scadenza del tempo t Data passa di nuovo su High. www.balluff.com italiano...
BTL7-S5 _ _ ( _ )-M _ _ _ _ -A/B/Y/Z(8)-S32/S115/S140/S147/KA _ _ /FA _ _ Sensore di posizionamento lineare magnetostrittivo — versione a barra Interfaccia SSI (continua) Funzionamento sincrono ed asincrono Nel funzionamento sincrono devono essere osservate due condizioni basilari: Funzionamento sincrono – La frequenza di scansione esterna f deve essere Per applicazioni tecnicamente corrette è...
Per il software PC ed il manuale relativo punto iniziale al punto finale viene emesso con un consultare in Internet l’indirizzo segnale positivo, mentre il movimento dal punto finale a www.balluff.com. quello iniziale viene indicato con un segnale negativo. Velocità (nessun segnale): velocità del datore di –...
Per UL: Uso in spazi chiusi e fino a un’altezza di 2000 m sul livello del Velocità max. rilevabile 10 m/s mare. Rilevazione singola secondo la norma interna Balluff Condizioni ambientali Frequenze di risonanza escluse Per UL: il BTL deve essere collegato esternamente mediante un circuito Temperatura ambiente −40…+85 °C...
2 kg/m lunghezza) Materiale corpo profilato alluminio Materiale flangia acciaio inox Materiale barra acciaio inox Spessore parete barra con Ø 8 mm 0,9 mm con Ø 10,2 mm 2 mm Fissaggio del corpo M18×1.5 o 3/4"-16UNF tramite filettatura Coppia di serraggio max. 100 Nm www.balluff.com italiano...
BTL7-S5 _ _ ( _ )-M _ _ _ _ -A/B/Y/Z(8)-S32/S115/S140/S147/KA _ _ /FA _ _ Sensore di posizionamento lineare magnetostrittivo — versione a barra Dati tecnici (continua) Collegamento con l’unità di valutazione La frequenza massima di scansione f , per la quale A,max risulta un nuovo valore ad ogni scansione, risulta dai seguenti grafici: in Hz A,max...
Dado di fissaggio 3/4"-16UNF: BTL-A-FK01-E-3/4"-16UNF BTL-P-1014-2R Fig. 9-1: Dimensioni montaggio datori di posizione BTL-P-0814-GR-PAF BTL-P-1013-4R, BTL-P-1013-4S, BTL-P-1012-4R, BTL-P-1014-2R: Peso: < 15 g Corpo: alluminio Contenuto nella fornitura del datore di posizione BTL-P-1013-4R, BTL-P-1013-4S, BTL-P-1012-4R: Distanziale: 8 mm, materiale poliossimetilene (POM) www.balluff.com italiano...
BTL7-S5 _ _ ( _ )-M _ _ _ _ -A/B/Y/Z(8)-S32/S115/S140/S147/KA _ _ /FA _ _ Sensore di posizionamento lineare magnetostrittivo — versione a barra Accessori (continua) Connettore S32 9.3.2 Confezionato Connettore diritto, incorporato, M16, a 8 poli È possibile ordinare diverse lunghezze del cavo, p. es. 9.3.1 Confezionabile liberamente BCC S518-0000-1Y-133-PS0825-050...
BTL7-S5 _ _ ( _ )-M _ _ _ _ -A/B/Y/Z(8)-S32/S115/S140/S147/KA _ _ /FA _ _ Sensore di posizionamento lineare magnetostrittivo — versione a barra Legenda codici di identificazione BTL7 Standard BTL7 - S 5 0 1 B - M0500 - B - S32 Interfaccia SSI Tensione di alimentazione: 5 = 10…30 V DC Formato dati:...
Seite 105
Z8 = filettatura in pollici 3/4"-16UNF, O-ring, diametro barra 8 mm Collegamento elettrico: S32 = connettore M16 a 8 poli secondo IEC 130-9 S115 = connettore M12, a 8 poli S140 = connettore, a 10 poli KA05 = cavo 5 m (PUR) FA05 = cavo 5 m (PTFE) www.balluff.com italiano...
Seite 109
Indicaciones sobre el servicio Interfaz SSI Principio Formatos de datos Consulta SSI errónea Servicio sincrónico y asincrónico Configuración con la BTL7 Configuration Tool (sólo para BTL7-S510(B)-…) BTL7 Configuration Tool Conexión del módulo de comunicación USB Posibilidades de configuración www.balluff.com español...
Seite 110
BTL7-S5 _ _ ( _ )-M _ _ _ _ -A/B/Y/Z(8)-S32/S115/S140/S147/KA _ _ /FA _ _ Sistema magnetostrictivo de medición de posición — forma constructiva de varilla Datos técnicos Precisión Condiciones ambientales Alimentación de tensión (externa) Líneas de comunicación La, Lb Salida Medidas, pesos Conexión a la unidad de evaluación Accesorios Sensores de posición Tuerca de fijación...
En la declaración de conformidad figura más información sobre las directivas, homologaciones y normas. Abreviaturas utilizadas No para BTL7-…-FA_ _ Interfaz de serie sincrónica (Synchronous Serial Patente estadounidense 5 923 164 Interface) La patente estadounidense se ha concedido en relación con este producto. www.balluff.com español...
óptimo según las indicaciones que figuran en los datos de señalización y se estructuran según el siguiente técnicos sólo se garantiza con accesorios originales de esquema: Balluff; el uso de otros componentes provoca la PALABRA DE SEÑALIZACIÓN exoneración de responsabilidad. Tipo y fuente de peligro No se permite la apertura del BTL o un uso indebido.
Diferencia de posición Zona de amortiguación: zona no aprovechable desde el – Velocidad (con o sin signo) punto de vista técnico de medición situada en el extremo – Diferencia de velocidad de la varilla y que se puede sobrepasar. www.balluff.com español...
BTL7-S5 _ _ ( _ )-M _ _ _ _ -A/B/Y/Z(8)-S32/S115/S140/S147/KA _ _ /FA _ _ Sistema magnetostrictivo de medición de posición — forma constructiva de varilla Estructura y funcionamiento (continuación) Comportamiento del LED 1 y el valor de error en toda la Indicador LED zona: LED 1 LED 2 Falta sensor de posición...
Fig. 4-4: Agujero roscado 3/4"-16UNF según SAE J475, 10,2 mm mínimo 13 mm junta tórica 15.3x2.4 8 mm mínimo 11 mm Sensor de posición: para el BTL están disponibles diferentes sensores de posición (véase Accesorios en la Tab. 4-1: Diámetro del orificio en el montaje en un cilindro hidráulico página 21). www.balluff.com español...
BTL7-S5 _ _ ( _ )-M _ _ _ _ -A/B/Y/Z(8)-S32/S115/S140/S147/KA _ _ /FA _ _ Sistema magnetostrictivo de medición de posición — forma constructiva de varilla Montaje y conexión (continuación) El elemento de deslizamiento se puede atornillar o pegar. Montar el BTL ► Asegure el tornillo para que no se suelte o pierda. ►...
Fig. 4-9: Asignación de pines S32 (vista desde arriba del conector en el BTL), conector cilíndrico M16 de 8 polos Fig. 4-11: Asignación de pines S140 (vista desde arriba del conector en el BTL), conector cilíndrico de 10 polos www.balluff.com español...
BTL7-S5 _ _ ( _ )-M _ _ _ _ -A/B/Y/Z(8)-S32/S115/S140/S147/KA _ _ /FA _ _ Sistema magnetostrictivo de medición de posición — forma constructiva de varilla Montaje y conexión (continuación) evaluación/control 4.4.4 Conector S147 BTL7 estándar Blindaje y tendido de cables BTL7-S5_ _…-S147 Puesta a tierra definida –Data El BTL y el armario eléctrico deben estar a +Data...
Indicaciones sobre el servicio – Compruebe periódicamente el funcionamiento del BTL y todos los componentes relacionados. – Si se producen fallos de funcionamiento, ponga fuera de servicio el BTL. – Asegure la instalación contra cualquier uso no autorizado. www.balluff.com español...
BTL7-S5 _ _ ( _ )-M _ _ _ _ -A/B/Y/Z(8)-S32/S115/S140/S147/KA _ _ /FA _ _ Sistema magnetostrictivo de medición de posición — forma constructiva de varilla Interfaz SSI Principio En el BTL7-S5_ _B/F-M… los datos de posición se determinan y emiten sincrónicamente para el período de SSI significa Synchronous Serial Interface y describe una exploración externo.
Low (bajo) tras finalizar la cantidad correcta de frecuencias. Con cada nuevo flanco negativo de Clk empieza de nuevo el temporizador t e internamente se establece el evento T . Tras finalizar el tiempo t Data pasa de nuevo a High (alto). www.balluff.com español...
BTL7-S5 _ _ ( _ )-M _ _ _ _ -A/B/Y/Z(8)-S32/S115/S140/S147/KA _ _ /FA _ _ Sistema magnetostrictivo de medición de posición — forma constructiva de varilla Interfaz SSI (continuación) Servicio sincrónico y asincrónico En el servicio sincrónico se deben tener en cuenta dos condiciones límite: Servicio sincrónico –...
Velocidad (sin signo): velocidad del sensor de – se pueden obtener en internet en la página posición, no se puede determinar la dirección de www.balluff.com. movimiento. Diferencia de posición: distancia entre dos sensores – de posición. La selección sólo es posible si se seleccionan dos sensores de posición.
Para UL: uso en espacios cerrados y hasta una altura de 2000 m sobre el Resolución velocidad 0,1 mm/s nivel del mar. Disposición individual según la norma de fábrica de Balluff Velocidad mín. detectable 1 mm/s Frecuencias de resonancias excluidas Velocidad máx. detectable 10 m/s...
Material de carcasa Aluminio Material de brida Acero inoxidable Material de la varilla Acero inoxidable Grosor de pared de la varilla con Ø 8 mm 0,9 mm con Ø 10,2 mm 2 mm Fijación de la carcasa M18×1.5 ó 3/4"-16UNF mediante rosca Par de apriete máx. 100 Nm www.balluff.com español...
BTL7-S5 _ _ ( _ )-M _ _ _ _ -A/B/Y/Z(8)-S32/S115/S140/S147/KA _ _ /FA _ _ Sistema magnetostrictivo de medición de posición — forma constructiva de varilla Datos técnicos (continuación) Conexión a la unidad de evaluación La frecuencia de exploración máxima f , con la cual con La frecuencia de exploración mínima f es de 62,5 Hz.
Fig. 9-1: Medidas de montaje de los sensores de posición BTL-P-0814-GR-PAF BTL-P-1013-4R, BTL-P-1013-4S, BTL-P-1012-4R, BTL-P-1014-2R: Peso: < 15 g Carcasa: Aluminio El volumen de suministro de los sensores de posición BTL-P-1013-4R, BTL-P-1013-4S, BTL-P-1012-4R incluye: Elemento 8 mm, material polioximetileno distanciador: (POM) www.balluff.com español...
BTL7-S5 _ _ ( _ )-M _ _ _ _ -A/B/Y/Z(8)-S32/S115/S140/S147/KA _ _ /FA _ _ Sistema magnetostrictivo de medición de posición — forma constructiva de varilla Código de modelo BTL7 estándar BTL7 - S 5 0 1 B - M0500 - B - S32 Interfaz SSI Tensión de alimentación: 5 = 10…30 V DC Formato de datos:...
Seite 131
Z8 = rosca inglesa 3/4"-16UNF, junta tórica, diámetro de varilla 8 mm Conexión eléctrica: S32 = 8 polos, conector M16 según IEC 130-9 S115 = 8 polos, conector M12 S140 = 10 polos, conector KA05 = cable de 5 m (PUR) FA05 = cable de 5 m (PTFE) www.balluff.com español...
BTL7-S5 _ _ ( _ )-M _ _ _ _ -A/B/Y/Z(8)-S32/S115/S140/S147/KA _ _ /FA _ _ Sistema magnetostrictivo de medición de posición — forma constructiva de varilla Anexo 11.1 Conversión de unidades de longitud 11.2 Placas de características 1 mm = 0,0393700787 pulgadas pulgadas 0,03937008 0,07874016 0,11811024 0,15748031 0,19685039 0,23622047 0,27559055 0,31496063 0,35433071...
Seite 134
US Service Center CN Service Center Germany Germany China Balluff GmbH Balluff GmbH Balluff Inc. Balluff (Shanghai) trading Co., ltd. Schurwaldstrasse 9 Schurwaldstrasse 9 8125 Holton Drive Room 1006, Pujian Rd. 145. 73765 Neuhausen a.d.F. 73765 Neuhausen a.d.F. Florence, KY 41042 Shanghai, 200127, P.R.