Redmond SkyKettle RK-G200S-E Handbuch Seite 8

2. Download the Ready for Sky application from the App Store or Google Play (de-
pending on the operating system of your device) to your smartphone or tablet.
Check the minimum supported version of the operating system on the official website
of www.redmond.company or in the description of the application in the App Store and
Google Play.
3. Start the Ready for Sky application, create an account, and follow the on-screen
prompts.
4. In the standby mode, press and hold down the button
appliance will produce three short beeps. During the connection, the temperature
indicators will come on alternately. Once the connection is established, the ap-
pliance will produce three short beeps.
If the Bluetooth function is disabled or the connection is not established within
30 seconds, the appliance will produce two short beeps and enter the standby mode.
5. To disable remote control, press and hold down the button
is produced. When the connection fails, the temperature indicators will blink.
To ensure stable communication, the mobile device should be no more than 15 meters
away from the appliance.
Appliance control via the wireless network. Instruction on the R4S Gateway applica-
tion installation is available through the link: www.readyforsky.com/r4sgateway
Bluetooth function
To enable Bluetooth:
1. Remove the kettle from the base.
2. Press and hold down the buttons
base.
3. The heating temperature indicators will come on for a few seconds and go off.
To disable Bluetooth:
1. Remove the kettle from the base.
2. Press and hold down the buttons
base.
3. The heating temperature indicators will blink three times and go off.
Water Boiling
1. Remove the kettle from the base. Press the lid release button.
8
for a few seconds, the
until a long beep
and to place the kettle back on the
and to place the kettle back on the
2. Pour water into the kettle, water level should be between the MIN and MAX points
on the scale. If water level is higher than MAX point, the boiling water may be
splashed. In case of water undersupply the appliance may be switched off in advance.
ATTENTION! The unit is intended only for water heating and boiling.
3. Close the kettle lid and set the kettle to the base. The appliance will be oper-
ated only if it is properly fixed.
4. Plug in the appliance. The heating temperature indicators will flash, the appliance
will switch to the standby mode.
5. Press . The short audible signal will be heard, water heating process will start,
the inner housing illumination will be enabled.
The flask illumination will change the color during heating.
6. After water comes to a boil three audible signals will be heard, the flask illumina-
tion will go off; the appliance will switch to the standby mode (no indicator light).
7. To interrupt the water heating process, press
the base.
Press the buttons on the control panel only with your fingertips, as shown in figure
(page 4). Pressing with your nails can damage the buttons!
A2
Water Heating Without Boiling
1. To heat water without boiling to 40, 55, 70, 85°C in the standby mode, select the
necessary temperature using (the indicator will come on next to the se-
lected value), press .
If the temperature in the kettle is higher than the adjusted heating temperature, three
audible signals will be heard after pressing
Warm mode.
2. After the end of water heating the appliance will make three short audio signals,
the flask illumination will go off, the appliance will switch to the Keep Warm
mode (the indicator of the maintained temperature value is lit).
3. To interrupt the Keep Warm mode, press
Temperature maintenance mode
This mode provides maintenance of the selected temperature 40, 55, 70, 85°С for 12
hours. If the temperature drops lower than the selected value, the heating element will
be automatically enabled. Water is not re-boiled. At the end of the process, the appliance
switches to the standby mode.
again or remove the kettle from
, the appliance will switch to the Keep
or remove the kettle from the base.