Cleaning The Filter - Livington SmartChill Gebrauchsanleitung

TIPS:
• Place the Livington SmartChill on a raised
surface, such as a table, desk, or sideboard.
• You will feel the effect greatest when sitting
directly in front of the Livington SmartChill.
• Even if the water tank is empty, the filter
remains wet and the Livington SmartChill
continues to cool.
• The colder the water used, the cooler the
effect. You can therefore also consider using
ice water or water with ice cubes.
• For best results, dampen the filter under
running water beforehand.
SETUP:
1. Place the Livington SmartChill on a level
surface. NOTE: Use the built-in cable guides on
the rear panel to keep the cable away from the
fan (see Fig. 1).
2. Open and fill the water tank (see Fig. 2): We
recommend using a jug or measuring cup. Do
not carry the appliance to fill it. Water could
leak or spill from it. Open the water tank door
and fill the tank to the MAX mark. Close the
water tank cover when finished.
3. Removing and moistening the filter: Open the
rear door on the appliance (see Fig. 3). Now
fold the black safety bar upwards (see Fig. 4)
and pull out the compartment that contains the
filter (Fig. 5). Now remove the filter (see Fig.
6). You can now dampen the filter. Note: For
best results, moisten slightly under running
water (see Fig. 7). For even greater cooling,
place the wet filter in the freezer until it is
frozen. Then place it back in the compartment
(ensuring that the black filter cover points
upwards), fold down the safety bar and close
the appliance door (see Fig. 8).
Note: The appliance will not work if the door is
open. This is a safety precaution.
4. Plug the narrower end of the cable into
the connector on the back of the Livington
SmartChill and plug the power adapter (GQ12-
120100-AG) into an electrical outlet (see Fig.
1). NOTE: Use the built-in cable guides along
the back to keep the cable away from the fan.
10
USE:
1. To turn on the Livington SmartChill, press the
on/off switch (see Fig. 9).
2. Set the speed of the fan by pressing the switch.
You can choose between low, medium and high
modes. The indicator lights next to the switch
show you the speed at which the Livington
SmartChill is currently running (see Fig. 9).
3. Air flow adjustment: Press the air flow control
button once to activate the swing function. The
blades on the appliance will now swivel. To fix
the blades in place, press the button again (see
Fig. 10).
4. Pressing the backlight button turns on night
lighting - the default setting is high brightness.
• Standard: Light on, high brightness
• Press once: Low brightness
• Press twice: Light off (see Fig. 11)
5. To turn off the Livington SmartChill, press the
button repeatedly until the fan turns off (one
press of the button after low speed) and the
mode indicator lights are no longer illuminated
(see Fig. 9).
CLEANING (see Fig. 12)
Disconnect the appliance from the power supply
before cleaning. We recommend cleaning the
water tank and the inside of the unit once a week.
Use a non-abrasive cloth and, if necessary, a
mild detergent. For best results, we recommend
replacing the filter every 3-6 months.
UNIT CLEANING
To prepare for cleaning, run Livington SmartChill
until all water has emptied from the water tank,
or hold the Livington SmartChill over a sink and
carefully drain to avoid splashing or spilling. If
you notice that the water tank is dirty, use a small
flexible brush (i.e. toothbrush, bottle brush, etc.)
and gently brush the inside of the tank until it is
clean. Rinse with warm water.

CLEANING THE FILTER

Remove the filter insert from the Livington
SmartChill. Using warm soapy water, wipe the
filter cartridge and tray, then rinse until clean.
!!Allow to air-dry completely!! (see Fig. 7)