Herunterladen Inhalt Inhalt
Teilen
Diese Seite drucken
Wasco EXDUL-581E Bedienungsanleitung
  1. Anleitungen
  2. Marken
  3. Wasco Anleitungen
  4. Module
  5. EXDUL-581E
  6. Bedienungsanleitung

Wasco EXDUL-581E Bedienungsanleitung

Vorschau ausblenden
Inhaltsverzeichnis

Werbung

Quicklinks

Diese Anleitung herunterladen
EXDUL-581E
EDP-No: A-371772
EXDUL-581S
EDP-No: 371760
8 A/D inputs 16-bit (single ended) or
4 A/D inputs16-bit (differential)
8 optocoupler isolated digital inputs
2 optocoupler isolated digital outputs
5 counters 32 bit
LCD display (EXDUL-581E only)
wasco
®
user's guide

Werbung

Inhaltsverzeichnis
loading

Verwandte Anleitungen für Wasco EXDUL-581E

Inhaltszusammenfassung für Wasco EXDUL-581E

  • Seite 1 EXDUL-581E EDP-No: A-371772 EXDUL-581S EDP-No: 371760 8 A/D inputs 16-bit (single ended) or 4 A/D inputs16-bit (differential) 8 optocoupler isolated digital inputs 2 optocoupler isolated digital outputs 5 counters 32 bit LCD display (EXDUL-581E only) wasco ® user‘s guide...
  • Seite 2 Important Information: This manual was made up for the modules EXDUL-581E and EXDUL-581S. EXDUL-581E additionally provides an LCD display, all other functions are identical. For the EXDUL-581S all commands and functions concerning the LCD display are not applicable.

  • Seite 3: Inhaltsverzeichnis

    4.8 Configuration with Static IP Address (DHCP deactivated)........14 4.9 Configuration with Dynamic IP Address (DHCP enabled) ........16 4.10 LCD Display during the Booting Process (EXDUL-581E only) ......17 4.11 LCD Display during Operation (EXDUL-581E only) ..........18 5. Accessing the EXDUL-581 ............19 5.1 Accessing via the EXDUL Web Page ..............19...
  • Seite 4 14.3 Wiring of the A/D Inputs single ended ..............97 14.4 Wiring of the A/D Inputs differential ..............98 15. ASCII Table ..................99 16. Product Liability Act ..............102 17. CE Declaration of Conformity ...........104 EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...

  • Seite 5: Introduction

    Special high power output optocouplers cope with a switching current up to 150 mA. If required, five of the optocoupler inputs can be programmed and used as 32-bit counter inputs. The EXDUL-581E comes with a programmable LCD display presenting I/O status information or programmable user- specific data.

  • Seite 6: Connection Terminals

    DIN1 / Counter1 DIN2 / Counter2 DIN3 / Counter3 DIN4 / Counter4 DIN5 DIN7 DIN6 DOUT+ DIN_COM DOUT1- DOUT0- GND_EXT Vcc_EXT Vcc_EXT: Connector for external voltage source GND_EXT: Ground connection EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...

  • Seite 7: System Components

    3.1 Block Diagram EXDUL-581E ext. Vcc +10V...+30V 16 Bit A/D Converter FIFO AIN00 - AIN07 Controller Optocoupler Outputs DOUT0 - DOUT1 Counter Optocoupler Inputs DIN0 - DIN7 Display Fig. 3.1 Block diagram EXDUL-581E EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...

  • Seite 8: Block Diagram Exdul-581S

    3.2 Block Diagram EXDUL-581S ext. Vcc +10V...+30V 16 Bit A/D Converter FIFO AIN00 - AIN07 Controller Optocoupler Outputs DOUT0 - DOUT1 Counter Optocoupler Inputs DIN0 - DIN7 Fig. 3.2 Block diagram EXDUL-581S EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...

  • Seite 9: A/D Inputs

    Counting frequency: max. 5 kHz 3.7 LCD Display (only EXDUL-581E) Matrix display with 2 lines and 16 columns displaying 16 characters each line Programmable to display user specific data or I/O state EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...

  • Seite 10: Deployment

    LED on the left side of the RJ45 jack is lit continuously. 4.2 Connecting the Operating Voltage The EXDUL-581E / EXDUL-581S requires a power supply of +10V ... +30V across terminal 23 (Vcc) and terminal 24 (GND). EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH...

  • Seite 11: Integrated Webpage Of Exdul-581E / Exdul-581S

    User name: admin Password: 11111111 Please observe upper and lower case! If you don’t succeed in accessing with this access code, your system administrator changed the settings of the access code. EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...

  • Seite 12: Default Setting Of The Network Configuration

    Example: If subnet mask 255.255.0.0 is allocated to the IP address 192.168.1.83, then the device is located in the network 192.168.-.- as device -.-.1.83. EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...

  • Seite 13: How To Change The Network Configuration

    DHCP service is available, for neither the PC nor the EXDUL provides one. In this case, the last set static IP address can be used for addressing the EXDUL-581. The IP address 169.254.1.1 is applicable for factory-new EXDUL devices. EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...

  • Seite 14: Configuration With Static Ip Address (Dhcp Deactivated)

    EXDUL-581 configuration screen. To change the configuration, connect the EXDUL-581 to a LAN or PC as per description in chapter 4.7 (How to change the network configuration). EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...
  • Seite 15 9 and the letters A through Z (leave out upper and lower case) and - (hyphen-minus). Some IP addresses are reserved or have special functions such as: 127.0.0.1 (local host). 192.168.1.0 (0 is the network address) with 255.255.255.0 (subnet mask). EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...

  • Seite 16: Configuration With Dynamic Ip Address (Dhcp Enabled)

    EXDUL web page. Clicking the TCP/IP Config button opens the configuration screen and you can acitivate DHCP by setting the checkmark Enable DHCP as shown in the following figure: EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...

  • Seite 17: Lcd Display During The Booting Process (Exdul-581E Only)

    ASCII digits 0 through 9 and the letters A through Z (leave out upper and lower case) and - (hyphen-minus). 4.10 LCD Display during the Booting Process (EXDUL-581E only) During booting-up the module, the display shows information data. Line 1 indicates the module name, line 2 displays the information that the module is being initialized.

  • Seite 18: Lcd Display During Operation (Exdul-581E Only)

    LCD display. In order to avoid „screen-burn“ during operation, the display alternates from I/O status display or UserLCD display to information display with the current IP address for approx. 5 seconds every minute. EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...

  • Seite 19: Accessing The Exdul-581

    ExdulUtility_v2_xx or later) you can open the web page. If you don‘t succeed in opening the EXDUL-581 web page, please check the network connections or the entered hostname. For more details see chapter FAQ - Troubleshooting. EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...

  • Seite 20: Accessing Via Tcp/Ip Sockets

    EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...

  • Seite 21: How To Identify Hostname, Ip Address And Mac Address

    EXDUL-5xx, the program needs to be allowed. The ExdulUtility_v2_xx search program (or a later version) is provided on the EXDUL software CD or available for download at www.messcomp. EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...

  • Seite 22: A/D Inputs 16 Bit

    As mentioned before, one byte for channel selection will be added to the command for measuring the voltage. Please see table 6.1 to choose the appropriate value for each channel when single ended measuring is used. EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...

  • Seite 23: Differential Operation

    + (-) rally occurring interference AIN06 & AIN07 (-) + voltages on both of the signal lines and the analog ground. Figure 6.2-1 A/D converter differential measurement EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...
  • Seite 24 An input voltage of +10V at AIN05 and an input voltage of -10V at AIN06 results in a difference of +20V, i.e. an input voltage range of +/- 20.4V must be chosen (see chapter 6.4) EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...

  • Seite 25: Combination Of Single Ended And Differential Measurement

    Input Voltage Range Byte Value Voltage +/- 20.4V (differential measuring only max +/- 10.2V → GND) +/-10.2V +/- 5.1V +/-2,55V +/-1.27V +/- 0.63V Table 6.4 A/D converter input voltage ranges EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...
  • Seite 26 = +20V diff AIN01 +20.4V or -20.4V (e.g. AIN00 = +10.2V and -10V AIN01 = -10.2V, V = 20.4V) diff -10.2V Fig. 6.4.3 EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...

  • Seite 27: Modes Of Measurement

    Duration = Number of channels*32*10µs After completion, the values are calibrated and returned to the user in µV. Example: Start 1st channel, 32 Measurements 2nd channel, 32 Measurements 3rd channel, 32 Measurements Fig. 6.5 EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...
  • Seite 28 It is important to ensure that the FIFO does not overflow. It is recommended to operate this measurement mode with a sampling rate of up to 20kS/s only. Additionally, you must not write to any EXDUL infor- mation register during this period. EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...

  • Seite 29: Adjustment Of The A/D Inputs

    A/D component can be adapted to the environ- ment by subsequent adjustment. The required software is provided on the enclosed CD or on the Internet. EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...

  • Seite 30: Optocoupler Inputs

    500 volts. The voltage within the input chan- nels is limited to 50 volts. 7.1 Pin assignment of the input optocouplers 16,14,12,10 15,13,11,9 1,3,5,7 2,4,6,8 Fig. 7.1 EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...

  • Seite 31: Input Circuitry

    ® 7.2 Input Circuitry Optocoupler Protection Diode DIN_COM Fig. 7.2 7.3 Input Current - 1,1V ≈ 3200Ω EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...

  • Seite 32: Optically Isolated Outputs

    500 volts. 8.1 Pin assignment of the output optocouplers 8.2 Optocoupler specifications Voltage collector-emitter: max. 50V Voltage emitter-collector: 0,1V Current collector-emitter: 150 mA 8.3 Output circuitry Optocoupler OUT..+ Schutzdiode OUT..- EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...

  • Seite 33: Information, Lcd And User Register

    The register Serial Number is a read-only register. The serial number in the table above serves as a format example. The line S/N shows each Hex value and the corresponding ASCII character as for the serial number 1044026. EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...

  • Seite 34: Memory Areas Usera, Userb, Userlcd1M* Und Userlcd2M

    The data in the registers UserLCD-line1 and UserLCD-line2 is not retained when switching off. You can adjust the LCD display contrast in register LCD contrast. This adjustment is retained when switching off. *: EXDUL-581E only, no application for EXDUL-581S EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...

  • Seite 35: Installing The Driver

    TCP/IP libraries are required, which are available in many high-level languages such as C, C++, C#, Visual Basic or Java. Access examples in several programming languages are provided on the enclosed CD or on our website www.mewsscomp.com. EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...

  • Seite 36: Programming

    EXDUL modules as uniform as possible. This facili- tates the user, if necessary, to switch from e.g. an Ethernet EXDUL module to a USB EXDUL module (for example EXDUL-581 -> EXDUL-381) without extensive programming efforts. EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...
  • Seite 37 Parameter: type: Info-Typ (see manual) Returned values: Returns the register "type" as a string Description: Reads the Module Information Register Info Area Info Byte UserA UserB Hardware Identifier Serial Number EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...
  • Seite 38 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Write the LCD-Modes: void SetLCDMode(byte mode) Parameter: mode: LCD mode Description: sets the LCD mode LCD Mode LCD Mode Byte IO Mode User Mode EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...
  • Seite 39 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH...
  • Seite 40 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH...
  • Seite 41 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH...
  • Seite 42 +/- 0.63V AIN05 AIN06 AIN07 Differential measuring AIN00+ / AIN01- AIN00- / AIN01+ AIN02+ / AIN03- AIN02- / AIN03+ AIN04+ / AIN05- AIN04- / AIN05+ AIN06+ / AIN07- AIN06- / AIN07+ EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...

  • Seite 43: Measuring Range

    +/- 0.63V AIN05 AIN06 AIN07 Differential measuring AIN00+ / AIN01- AIN00- / AIN01+ AIN02+ / AIN03- AIN02- / AIN03+ AIN04+ / AIN05- AIN04- / AIN05+ AIN06+ / AIN07- AIN06- / AIN07+ EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...
  • Seite 44 +/- 0.63V AIN05 AIN06 AIN07 Differential measuring AIN00+ / AIN01- AIN00- / AIN01+ AIN02+ / AIN03- AIN02- / AIN03+ AIN04+ / AIN05- AIN04- / AIN05+ AIN06+ / AIN07- AIN06- / AIN07+ EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...
  • Seite 45 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH...
  • Seite 46 +/- 0.63V AIN05 AIN06 AIN07 Differential measuring AIN00+ / AIN01- AIN00- / AIN01+ AIN02+ / AIN03- AIN02- / AIN03+ AIN04+ / AIN05- AIN04- / AIN05+ AIN06+ / AIN07- AIN06- / AIN07+ EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...
  • Seite 47 +/- 0.63V AIN05 AIN06 AIN07 Differential measuring AIN00+ / AIN01- AIN00- / AIN01+ AIN02+ / AIN03- AIN02- / AIN03+ AIN04+ / AIN05- AIN04- / AIN05+ AIN06+ / AIN07- AIN06- / AIN07+ EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...
  • Seite 48 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Factory Reset: void DefaultReset() Description: Resets the module to the factory settings. After this command the module has to be shut down and restarted again. EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...

  • Seite 49: Programming With Tcp-Libraries

    The last result or confirmation string has to be read before transmitting a new string. Module 4 + n Byte Command1 4 + m Byte Reply1 4 + x Byte Command2 4 + y Byte Reply2 Fig. 11.2 Communication model EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...
  • Seite 50 The number of the 4 byte blocks varies from command to command and depends in part on the volume of data to be transmitted. More detailed information can be found in the individual command descriptions. EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...

  • Seite 51: Password Protection

    8 more bytes have been appended holding the password. Additionally, the length byte has to be increased by 2 (+8 bytes). The response does not contain a password and corresponds to the usual response array without a password. EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...

  • Seite 52: Command Overview

    Start AD continuous sampling 0A 00 0B Stop AD continuous sampling 09 00 00 Counter0 09 00 01 Counter1 09 00 02 Counter2 09 00 03 Counter3 09 00 04 Counter4 EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...
  • Seite 53 Data 11th character [blank] asci Data 12th character [blank] asci Data 13th character [blank] asci Data 14th character [blank] asci Data 15th character [blank] asci Data 16th character [blank] asci EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...
  • Seite 54 Data 11th character [blank] asci Data 12th character [blank] asci Data 13th character [blank] asci Data 14th character [blank] asci Data 15th character [blank] asci Data 16th character [blank] asci EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...
  • Seite 55 Data 11th character [blank] asci Data 12th character [blank] asci Data 13th character [blank] asci Data 14th character [blank] asci Data 15th character [blank] asci Data 16th character [blank] asci EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...
  • Seite 56 Data 3rd character 4 Read function info area Data 4th character 4 Data 5th character 0 Data 6th character 2 Data 7th character 6 reserved reserved reserved reserved reserved reserved reserved reserved reserved EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...
  • Seite 57 Data 11th character [blank] asci Data 12th character [blank] asci Data 13th character [blank] asci Data 14th character [blank] asci Data 15th character [blank] asci Data 16th character [blank] asci EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...
  • Seite 58 UserLCD1m or UserLCD2m at module start. All of the registers are readable as whole 16-byte blocks only. LCD Command LCD Command Byte UserLCD1 & UserLCD2 UserLCD1m & UserLCD2m EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...
  • Seite 59 Data Line2 12th character [blank] asci Data Line2 13th character [blank] asci Data Line2 14th character [blank] asci Data Line2 15th character [blank] asci Data Line2 16th character [blank] asci EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...
  • Seite 60 Command code 3rd Byte Length byte → 8 Byte Length byte → 0 Byte LCD Command LCD mode reserved reserved Write function 00 (IO Mode) LCD mode 01 (User Mode) reserved reserved reserved EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...
  • Seite 61 Command code 3rd Byte Length byte → 4 Byte Length byte → 4 Byte 00 (IO-Mode) LCD command LCD mode LCD mode 01 (User-Mode) reserved reserved reserved reserved read function reserved EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...
  • Seite 62 Length byte → 4 Byte Length byte → 4 Byte LCD command LCD contrast Contrast value (Lowbyte - 00...FF) reserved Contrast value (Highbyte - 00...0F) reserved reserved read function reserved EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...
  • Seite 63 Hostname 16th character [blank] asci 4th Byte IP address decimal value 63 3rd Byte IP address decimal value 0 2nd Byte IP address decimal value168 1st Byte IP address decimal value 192 EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...
  • Seite 64 Secondary DNS 3rd Byte decimal value 151 Secondary DNS 2nd Byte decimal value 237 Secondary DNS 1st Byte decimal value 217 DCHP client configuration 00 (DHCP disable) 01 (DHCP enable) reserved reserved reserved EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...
  • Seite 65 1st Byte IP address decimal value 192 4th Byte Subnetmask decimal value 0 3rd Byte Subnetmask decimal value 255 2nd Byte Subnetmask decimal value 255 1st Byte Subnetmask decimal value 255 EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...
  • Seite 66 01 (DHCP enable) Reserved Reserved Reserved Reserved Reserved MAC address 6th character MAC address 5th character MAC address 4th character MAC address 3rd character MAC address 2nd character MAC address 1st character EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...
  • Seite 67 Command code 1st Byte Command code 2nd Byte Command code 3rd Byte Length byte → 20 Byte 00 (Password deactivated) Security Byte 01 (Password activated) reserved reserved Write function Security configuration EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...
  • Seite 68 Command code 1st Byte Command code 2nd Byte Command code 3rd Byte Length byte → 20 Byte 00 (Password deactivated) Security Byte 01 (Password activated) reserved reserved Read function Security configuration EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...
  • Seite 69 Password 3rd character D asci Password 4th character U asci Password 5th character L asci Password 6th character 5 asci Password 7th character 8 asci Password 8th character 1 asci EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...
  • Seite 70 Byte Transmit Receive Representing Command code 1st Byte Command code 2nd Byte Command code 3rd Byte 01 (→ 4Byte) Length byte r/w Byte (0→ write) Optocoupler output state reserved reserved EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...
  • Seite 71 Command code 1st Byte Command code 2nd Byte Command code 2nd Byte Command code 3rd Byte Command code 3rd Byte 01 (→ 4Byte) Length byte Length byte Optocoupler input state reserved reserved reserved EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...
  • Seite 72 Command code 3rd Byte Command code 3rd Byte Length byte Length byte Counter command code start counter0 Counter command code stop counter0 reset counter0 reserved reserved reserved reserved reserved reserved EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...
  • Seite 73 Command code 3rd Byte Command code 3rd Byte 01 (→ 4Byte) Length byte Length byte Counter command code Counter command code Reset overflow flag Reset overflow flag reserved reserved reserved reserved reserved reserved EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...

  • Seite 74: Measuring Range

    Measured value Byte0 Range byte Measured value Byte1 Measured value Byte2 Measured value Byte3 Voltage = (integer) (Byte3 * 0x1000000 + Byte2 * 0x10000 + Byte1 * 0x100 + Byte0) [µV] EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...
  • Seite 75 Range byte Measured value Byte1 reserved Measured value Byte2 reserved Measured value Byte3 Voltage = (integer) (Byte3 * 0x1000000 + Byte2 * 0x10000 + Byte1 * 0x100 + Byte0) [µV] EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...
  • Seite 76 3 + n*4 Channel byte 4 + n*4 +1 Measured value Byte1 4 + n*4 Range byte 4 + n*4 +2 Measured value Byte2 4 + n*4 +3 Measured value Byte3 EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...
  • Seite 77 * 0x10000 + Byte1 * 0x100 + Byte0 ) [µV] Measured value AIN04 = (integer) (Byte3 * 0x1000000 + Byte2 * 0x10000 + Byte1 * 0x100 + Byte0 ) [µV] EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...
  • Seite 78 Command code 2nd Byte Command code 3rd Byte Command code 3rd Byte Length byte → 4 Bytes Length byte Overflow flag 00 FIFO no overflow 01 FIFO overflow reserved reserved reserved EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...

  • Seite 79: Command Structure

    Measured value Byte1 Measured value Byte2 Measured value Byte3 Measured value Byte0 n*4 + 1 Measured value Byte1 n*4 + 2 Measured value Byte2 n*4 + 3 Measured value Byte3 EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...
  • Seite 80 Length byte → 8 bytes Length byte Measured value Byte0 Measured value Byte1 Measured value Byte2 Measured value Byte3 Measured value Byte0 Measured value Byte1 Measured value Byte2 Measured value Byte3 EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...
  • Seite 81 (command + length byte) length byte > 0 There are 4 Bytes of length byte in the receiving buffer FIFO is empty read 4 Bytes of length byte receiving routine completed EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...
  • Seite 82 +/- 0.63V AIN05 AIN06 AIN07 Differential measuring AIN00+ / AIN01- AIN00- / AIN01+ AIN02+ / AIN03- AIN02- / AIN03+ AIN04+ / AIN05- AIN04- / AIN05+ AIN06+ / AIN07- AIN06- / AIN07+ EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...
  • Seite 83 + 10 Channel byte n*4 + 11 Range byte Sampling rate = Byte2 * 65536 + Byte1 * 256 + Byte0 Number of readings = Byte1 * 256 + Byte0 EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...
  • Seite 84 +/- 0.63V AIN05 AIN06 AIN07 Differential measuring AIN00+ / AIN01- AIN00- / AIN01+ AIN02+ / AIN03- AIN02- / AIN03+ AIN04+ / AIN05- AIN04- / AIN05+ AIN06+ / AIN07- AIN06- / AIN07+ EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...
  • Seite 85 Receive Representing Command code 1st Byte Command code 1st Byte Command code 2nd Byte Command code 2nd Byte Command code 3rd Byte Command code 3rd Byte Length byte Length byte EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...

  • Seite 86: Access To The Module Via Labview And Exdul.dll

    Due to the EXDUL.dll., the module can be integrated into a LABView project without much effort. Along with the .NET.Framework additionally LABView and the EXDUL.dll file is required on the computer. We refer to the EXDUL-LABView Tutorial for more detailed information. EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...

  • Seite 87: Faq - Trouble Shooting

    EXDUL-581 and computer (a crossover cable might be required). For network operation, check network cables between EXDUL-581 and the wall-mounted network socket, the active Ethernet switch or the Ethernet hub. EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...
  • Seite 88 ID and a device ID. The Subnet mask separates the IP address in a network part (network prefix, network ID) and a device part (device ID). EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...
  • Seite 89 For this, switch to the MS-DOS prompt (see „How to switch to MS-DOS prompt“), type ipconfig and press enter to confirm. The response should look similar to the following figure: EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...

  • Seite 90: Windows Xp

    Start -> ControlPanel -> Network & Connections -> Local Area Connection -> right mouse botton to Properties -> highlight Internet Protocol (TCP/ IP) -> Properties Please note: you have to own administrator privileges for changing TCP/ IP settings! EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...
  • Seite 91 EXDUL-5xx directly connected to a PC as well as for a network connected via hub or switch with several modules. In case the firewall prevents the searching program from communicating with the EXDUL-5xx a release is required. EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...

  • Seite 92: Specifications

    Counting frequency: max. 5 kHz LCD Display (EXDUL-581E only) Matrix display with 2 lines and 16 columns displaying 16 characters each line Programmable to display application-specific data or representing I/O status EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...
  • Seite 93 Insulating plastic housing with integrated snap-in technology for DIN EN top hat rail mounting. Suitable for control and engineering technology mounted to control and distribution boxes, surface mounting or mobile use on a desk. EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...

  • Seite 94: Circuitry Examples

    Circuit breaker closed = „1“ Circuit breaker DIN0 + 24V (V DIN1 DIN2 DIN3 DIN4 DIN5 DIN6 DIN7 Schematic circuit diagram DIN_COM (GND Figure 14.1.1 Wiring of the Optocoupler Inputs EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...
  • Seite 95 Circuit breaker closed = „1“ Circuit breaker DIN0 (GND DIN1 DIN2 DIN3 DIN4 DIN5 DIN6 DIN7 Schematic circuit diagram DIN_COM + 24V (V Fig 14.1.2 Wiring of the optocoupler inputs revers EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...

  • Seite 96: Wiring Of The Optocoupler Outputs

    ® 14.2 Wiring of the Optocoupler Outputs EXDUL-581 Electrical loads DOUT0+ + 24V (V e.g. lamp, relays,actuator DOUT1+ DOUT0...01- (GND Schematic circuit diagram Figure 14.2 Optocoupler output wiring EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...

  • Seite 97: Wiring Of The A/D Inputs Single Ended

    ® 14.3 Wiring of the A/D Inputs single ended Internal External AIN00 AIN01 Multiplexer Range Selection unwired Channels AIN07 ADGND Figure 14.3 Wiring of the A/D inputs (single ended) EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...

  • Seite 98: Wiring Of The A/D Inputs Differential

    ® 14.4 Wiring of the A/D Inputs differential Internal External AIN00 AIN02 AIN06 Multiplexer Range Selection AIN01 AIN03 AIN07 unwired inputs ADGND Figure 14.4 Wiring of the A/D inputs (differential) EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...

  • Seite 99: Ascii Table

    00011011 01000011 00011100 01000100 00011101 01000101 00011110 01000110 00011111 01000111 00100000 [space] 01001000 00100001 01001001 „ 00100010 01001010 00100011 01001011 00100100 01001100 00100101 01001101 00100110 & 01001110 ‚ 00100111 01001111 EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...
  • Seite 100 01101101 10011001 01101110 10011010 01101111 10011011 01110000 10011100 01110001 10011101 01110010 10011110 01110011 10011111 01110100 10100000 01110101 10100001 01110110 10100010 01110111 10100011 01111000 10100100 01111001 10100101 01111010 10100110 01111011 10100111 EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...
  • Seite 101 11000101 11110001 11000110 11110010 11000111 11110011 11001000 11110100 11001001 11110101 11001010 11110110 11001011 11110111 11001100 11111000 11001101 11111001 11001110 11111010 11001111 11111011 11010000 11111100 11010001 11111101 11010010 11111110 11010011 11111111 EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...

  • Seite 102: Product Liability Act

    Particular attention must be drawn to the following instructions: VDE100; VDE0550/0551; VDE0700; VDE0711; VDE0860. You can obtain the instructions from: vde-Verlag GmbH Bismarckstr. 33 10625 Berlin EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...
  • Seite 103 Furthermore, the compliance with building and safety instructions of all kinds (VDE, TÜV, industrial injuries corporation, etc.) is subject to the user/customer. EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...

  • Seite 104: Ce Declaration Of Conformity

    EN 50082-1 EN 60555-2 EN 60555-3 The following manufacturer is responsible for this declaration: Messcomp Datentechnik GmbH Neudecker Str. 11 83512 Wasserburg issued by Dipl.Ing.(FH) Hans Schnellhammer Wasserburg, 31.01.2019 ________________________________ EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...
  • Seite 105 804-530061C 802-563424J 802-561589J 19" Gehäuse: Vero PC-Gehäuse 145-010108L 19" Gehäuse: Zusatzelektronik 519-112111C Motherboard: GA-586HX PIV 1.55 Floppy-Controller: auf Motherboard Floppy: TEAC FD-235HF Grafikkarte: Advantech PCA-6443 Schnittstellen: EXDUL-581E A-371772 EXDUL-581S A-371760 EXDUL-581E / EXDUL-581S © 2019 by Messcomp Datentechnik GmbH EV03...

Diese Anleitung auch für:

Exdul-581s

Inhaltsverzeichnis