THOMSON ROC1404 Bedienungsanleitung Seite 5

This universal remote control is compatible with most television sets controlled by infra-red.
This remote control was programmed in the factory, so that you can use it to control most of
the sets of the THOMSON group's make. For this reason, we recommend that prior to
attempting to programme the remote control, you try it out by means of one of the methods
described in this user manual. However, first of all, you must install 2 batteries (AAA) in the
remote control.
Please keep this guide along with the code list (provided separately), so that you can
subsequently programme your remote control for use with other sets.
The keys
1 Indicator light: the red indicator light is lit whenever
a key is pressed.
2 On/Standby or Standby only, depending on the
equipment being used.
3 Activation and use of teletext (Videotext).
4 Selection of channels, input of digital values,
channels with 2 digits, external TV/VIDEO sources
(AV connectors).
5 Mute.
6 Programming of the remote control.
7 Activation and use of menus (display, deletion,
choice, confirmation).
8 Zapping and volume control.
9 Use of teletext (Fastext) or functions specific to
certain devices.
Note: depending on the actual devices, manufacturers
and year of manufacture, the functions available will
vary.
Testing the remote control
before programming
1. Switch on the set you want to control.
2. Direct the remote control towards the TV set and try
to switch it off by simply pressing the key B . If the
device does not turn off, you must program the
remote control using one of the methods A, B, C or
D described hereafter.
Programming
the remote control
Method A – Fast programming
with 1-digit subcode
Before you start programming, you must find the
subcode of the set to be controlled.
Refer to the list provided with these instructions, page I
of the subcodes.
1. Switch on the set you want to control.
2. Hold down the S key until the red indicator light
blinks 3 times and then remains lit (the indicator
light remains on for a few seconds to give you the
time to proceed with the following steps. The
indicator lamp flashes to signal that this time is
almost up, and then goes off).
3. While the indicator is lit, type in the subcode
(example: 1 for THOMSON).
4. Direct the remote control towards the set and try to
switch it off by pressing the key B .
5. If the set you want to control switches off, press OK
to memorise the subcode.
6. Should the set not switch off, press key B
repeatedly, until the set switches off. Between
pressing the keys, be sure to leave enough time for
the indicator light to go out and then relight (about
1 second). Proceeding this way will enable you to
see whether the set responds or not.
7. Immediately upon the switching-off of the set to be
controlled, press OK to store the subcode.
Check of the programming:
In principle, your set is ready for receiving the remote
control commands.
Check your remote control for proper functioning by
performing the test described on page 2.
Method B – 3-digit codes
programming
Before you start programming, you must find the code
of the set to be controlled.
Refer to the list provided with these instructions, page II
of the codes.
1. Switch on the set you want to control.
2. Hold down the S key until the red indicator light
blinks 3 times and then remains lit (the indicator
light remains on for a few seconds to give you the
time to proceed with the following steps. The
indicator lamp flashes to signal that this time is
almost up, and then goes off).
3. While the indicator is lit, enter the first digit of the
3-digit code proposed for the set to be controlled
(example: 036 for Thomson).
4. Direct the remote control towards the set and try to
switch it off by pressing the key B .
5. Should the set not switch off, repeat step 2. Then
type in the next 3-digit code. Try to switch off the set
by pressing key B once. Repeat this procedure by
trying out each of the 3-digit codes.
Check of the programming:
In principle, your set is ready for receiving the remote
control commands.
Check your remote control for proper functioning by
performing the test described on page 2.
Method C – Programming by means
of code retrieval
Should none of the codes work, you still have the
possibility of retrieving the appropriate code without
having to perform any input.
1. Switch on the set you want to control.
2. Hold down the S key until the red indicator light
blinks 3 times and then remains lit.
3. Direct the remote control towards the set and try to
switch it off by pressing the key B .
4. If the set you want to control switches off, press OK
to memorise the subcode.
5. Should the set not switch off, press key B as many
times as required (up to 200 times), until the set
switches off. Between pressing the keys, be sure to
leave enough time for the indicator light to go out
and then relight (about 1 second). Proceeding this
way will enable you to see whether the set responds
or not.
6. Immediately upon the switching-off of the set to be
controlled, press OK to store the code.
Check of the programming:
In principle, your set is ready for receiving the remote
control commands.
Check your remote control for proper functioning by
performing the test described on page 2.
Try out other remote control keys to find out the range
of functions you can control. If you think that not all of
the keys are active, repeat the procedure of this
programming method to find out the code supporting a
wider range of features.
1