Makita DMR203 Betriebsanleitung Seite 8

NOTE:
Depending on the conditions of use and the ambient
temperature, the indication may differ slightly from the
actual capacity.
Using supplied AC power adaptor
Remove the rubber protector and insert the adaptor
plug into the DC socket on the right hand side of the
speaker. Plug the adaptor into a standard mains socket
outlet. Whenever the adaptor is used, the battery pack
is automatically disconnected.
CAUTION:
● Always disconnect the AC power adaptor
completely before moving the speaker. If the AC
adaptor is not removed, it may cause an electric
shock.
● Never pull and/or drag the cord of the adaptor.
If not, the speaker may accidentally fall down,
causing injury to you or someone around you.
IMPORTANT:
● The mains adaptor is used as the means of
connecting the speaker to the mains supply. The
mains socket used for the speaker must remain
accessible during normal use.
● In order to disconnect the speaker, the mains adaptor
should be removed from the mains outlet completely.
● Use the AC power adaptor supplied with the product
or specified by Makita only.
● Do not hold the power supply cable and plug by your
mouth. Doing so might cause an electric shock.
● Do not touch the power plug with wet or greasy hands.
● Damaged or entangled cords increase the risk
of electric shock. If the cord is damaged, have it
replaced by our authorized service center in order to
avoid a safety hazard. Do not use it before repair.
● After use, always store AC power adaptor out of the
reach of children. If Children play with the cord, they
may suffer injury.
USB power supply socket
This jack can be used to charge a mobile phone or any
other device that uses less than 2.1A of DC current.
Charging will only occur when the speaker is switched
on.
NOTE:
Ensure the specification of your external device such as
mobile phone or player is compatible with the speaker.
Please read instruction manual of your external device
before charging.
IMPORTANT:
● Before connecting USB device to the charger, always
backup your data of USB device. Otherwise your data
may lose by any possibility.
● The charger may not supply power to some USB
devices.
● When not using or after charging, remove the USB
cable and close the cover.
● Do not connect power source to USB port. Otherwise
there is risk of fire. The USB port is only intended
for charging lower voltage device. Always place the
cover onto the USB port when not charging the lower
voltage device.
● Do not insert a nail, wire, etc. into USB power supply
port. Otherwise a circuit short may cause smoke and
fire.
● Do not connect this USB socket with your PC
USB port, as it is highly possible that it may cause
breakdown of the units.
LISTENING TO MUSIC VIA
BLUETOOTH STREAMING
You need to pair your Bluetooth device with the speaker
before you can auto-link to play/stream Bluetooth music
through the speaker. Pairing creates a 'bond' so two
devices can recognize each other.
Note:
To have the better sound quality, we recommend
setting the volume to more than two-thirds level on your
Bluetooth device and then adjust the volume on the
speaker as required.
Pairing your Bluetooth device for the
first time
1. Press the Power button to turn on the speaker.
"Pairing" will appear on the display to show the
speaker is discoverable.
2. Activate Bluetooth on your device according to the
device's user manual to link to the speaker. Locate
the Bluetooth device list and select the device named
"DMR203" (With some mobiles which are equipped
with earlier versions than BT2.1 Bluetooth device,
you may need to input the pass code "0000").
3. Once connected, there will be a confirmation tone
sound. "Paired" will appear on the display. You can
simply select and play any music from your source
device. Volume control can be adjusted from your
source device, or directly from the speaker.
4. Use the controls on your Bluetooth-enabled device or
on the speaker to play/pause and navigate tracks.
Note:
● If 2 Bluetooth devices, pairing for the first time, both
search for the speaker, it will show its availability on
both devices. However, if one device links with this
unit first, then the other Bluetooth device won't find it
on the list.
● If your Bluetooth device is temporarily disconnected
to the speaker, then you need to manually reconnect
your device again to the speaker.
8 ENGLISH