Before Starting The Equipment - EINHELL GE-CM 18 Li Set Originalbetriebsanleitung

Residual risks
Even if you use this electric power tool in
accordance with the instructions, certain
residual risks cannot be eliminated. The fol-
lowing hazards may arise in connection with
the equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is applied.
Warning!
This equipment generates an electromag-
netic fi eld during operation. Under certain
circumstances this fi eld may actively or pas-
sively impede medical implants. To reduce
the risk of serious or fatal injuries, we recom-
mend persons with medical implants to con-
sult their doctor and the manufacturer of the
medical implant prior to using the equipment.

5. Before starting the equipment

The lawn mower is delivered partly assembled.
The push bar and the grass basket must be
assembled before using the lawn mower. Follow
the instructions step by step and refer to the
pictures when assembling.
Warning! Always pull out the safety plug be-
fore making adjustments to the equipment.
Fitting the push bar (Fig. 3a to 3c)
Take a bottom push bar (Fig. 2 /Item 3) and fasten
it with the nut (Fig. 2/Item 13) as shown in Fig. 3a.
Proceed in the same way on the other side. Screw
the top push bar (Fig. 2/Item 2) to the bottom
push bar (Fig. 2/Item 3) as shown in Fig. 3b.
Then attach the power cable to the push bar (Fig.
2/Item 14) using the cable clips (Fig. 3c).
Mounting the grass basket (Fig. 4a to 4c)
Plug the bottom and the top part of the grass box
together (Fig. 4a/Item 9, 10). Ensure that all the
plastic lugs engage correctly. Next push the grass
box handle (Fig. 4b/Item 11) into the openings on
the grass box. Check that the handle is secure
and correctly positioned. Before you fi t the grass
basket you must ensure that the motor is swit-
ched off and the blade is not rotating.
The grass box must be attached to the two hooks
on the mower. To do this, open the ejector fl ap
with one hand (Fig. 4c/Item 7) and attach the
Anl_GE_CM_18_Li_Set_SPK7.indb 115 Anl_GE_CM_18_Li_Set_SPK7.indb 115
GB
grass box with the other hand. The ejector fl ap is
held against the grass box by a spring.
Adjusting the cutting height
Warning!
Adjust the cutting height only when the motor has
been switched off and the safety plug has been
disconnected.
Before you begin to mow, check to ensure that the
blade is not blunt and that none of the fasteners
are damaged. To prevent any imbalance, replace
blunt and/or damaged blades. To carry out this
check, fi rst switch off the motor and pull out the
safety plug.
The cutting height is adjusted as shown in Figure
5. To do so, turn the equipment upside down or tilt
it to the side. Position both the front and rear axle
in the same notch, so that the cutting blade runs
parallel to the lawn.
Position Cutting depth
1 70mm
2 50mm
3 30mm
Charging the battery (Fig. 6)
1. Take the battery pack out of the equipment.
Do this by pressing the side pushlock buttons.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(17) into the socket outlet. The green LED will
then begin to fl ash.
3. Insert the battery pack (16) into the battery
charger (17).
4. In the section entitled „Charger indicator" you
will fi nd a table with an explanation of the LED
indicator on the charger.
The battery pack can become a little warm during
the charging. This is normal.
If the battery pack fails to charge, check:
•
whether there is voltage at the socket outlet
•
whether there is good contact at the charging
contacts
If the battery pack still fails to charge, send
•
the charging unit
•
and the battery pack
to our customer service center.
- 115 -
19.09.2018 08:45:24 19.09.2018 08:45:24