Functional Description - Makita GD0600 Bedienungsanleitung

the rotating accessory which in turn causes the
uncontrolled power tool to be forced in the direction
opposite of the accessory's rotation at the point of the
binding.
For example, if an abrasive wheel is snagged or pinched
by the workpiece, the edge of the wheel that is entering
into the pinch point can dig into the surface of the
material causing the wheel to climb out or kick out. The
wheel may either jump toward or away from the operator,
depending on direction of the wheel's movement at the
point of pinching. Abrasive wheels may also break under
these conditions.
Kickback is the result of power tool misuse and/or
incorrect operating procedures or conditions and can be
avoided by taking proper precautions as given below.
a) Maintain a firm grip on the power tool and
position your body and arm to allow you to
resist kickback forces. Always use auxiliary
handle, if provided, for maximum control over
kickback or torque reaction during start-up.
The operator can control torque reactions or
kickback forces, if proper precautions are taken.
b) Never place your hand near the rotating
accessory. Accessory may kickback over your
hand.
c) Do not position your body in the area where
power tool will move if kickback occurs.
Kickback will propel the tool in direction opposite to
the wheel's movement at the point of snagging.
d) Use special care when working corners,
sharp edges etc. Avoid bouncing and snagging
the accessory. Corners, sharp edges or bouncing
have a tendency to snag the rotating accessory
and cause loss of control or kickback.
Safety Warnings Specific for Grinding:
a) Use only wheel types that are recommended
for your power tool.
b) Wheels must be used only for recommended
applications. For example: do not grind with
the side of cut-off wheel. Abrasive cut-off wheels
are intended for peripheral grinding, side forces
applied to these wheels may cause them to
shatter.
c) Always use undamaged wheel flanges that
are of correct size and shape for your selected
wheel. Proper wheel flanges support the wheel
thus reducing the possibility of wheel breakage.
d) Do not use worn down wheels from larger
power tools. Wheel intended for larger power tool
is not suitable for the higher speed of a smaller tool
and may burst.
Additional safety warnings:
16. Observe the instructions of the manufacturer
for correct mounting and use of wheels.
Handle and store wheels with care.
17. Check that
supported.
the workpiece is
18. Make sure the wheel is not contacting the
workpiece before the switch is turned on.
19. Keep hands away from rotating parts.
20. Do not touch the workpiece immediately after
operation; it may be extremely hot and could
burn your skin.
21. Always be sure you have a firm footing. Be
sure no one is below when using the tool in
high locations.
22. Do not use the tool on any materials
containing asbestos.
23. Before using the tool on an actual workpiece,
let it run for a while. Watch for vibration or
wobbling that could indicate poor installation
or a poorly balanced wheel.
24. Do not use this tool as cutter.
SAVE THESE INSTRUCTIONS.
WARNING:
MISUSE or failure to follow the safety rules stated in
this instruction manual may cause serious personal
injury.

FUNCTIONAL DESCRIPTION

CAUTION:
Always be sure that the tool is switched off and
•
unplugged before adjusting or checking function on
the tool.
Switch action
Fig.1
CAUTION:
Before plugging in the tool, always check to see
•
that the switch lever actuates properly and returns
to the "OFF" position when released.
Do not pull the switch lever forcibly without pushing
•
in the lock-off lever.
For tool with lock button
To prevent the switch lever from accidentally pulled, a
lock-off lever is provided. To start the tool, pull the
lock-off lever toward the operator and then pull the
switch lever. Release the switch lever to stop. For
continuous operation, pull the switch lever and then
push in the lock button. To stop the tool from the locked
position, pull the switch lever fully, then release it.
For tool without lock button
To prevent the switch lever from accidentally pulled, a
lock-off lever is provided. To start the tool, pull the
lock-off lever toward the operator and then pull the
switch lever. Release the switch lever to stop.
properly
5