Jacuzzi sasha Montageanweisung Seite 21

frame, as indicated (resting against the front cover).
(detail 3) Place the silicone in the indicated areas.
✐
21, details 1-2) After having measured the length, cut
■ (
some sections from the sealant roll which must be applied to
the inner edge of the following profiles:
- the glass panels/the small panels/ (lower, vertical and upper side).
- the glass panels/the large panels/ (lower, vertical and upper side).
NOTE: it is recommended to cut approx. 5 cm more of the sealant
than the nominal length and then remove any remaining length
once assembly is complete.
Installing roofs
Sasha (Sauna / Hammam); Sasha white (Hammam)
✐
22) Apply the metal corners to the roof, as indicated.
■ (
Sauna models
Sasha: ✐
23, detail 1-2) (
■ (
Unwind the sensor cable and bring it near the electronic box, as
indicated.
Sasha: ✐
■ ( 23, detail 3) (
tion the roof so that it rests on the relevant frame. Adjust its position,
by lifting it as much as is needed to move it outwards and close any
openings between frame and roof.
Sasha: ✐
23, detail 4) (
■ (
nect the sensor cable to the terminal indicated.
Hamam models
Sasha / Sasha white: ✐
■ (
to the roof.
Sasha / Sasha white: ✐
■ (
cable and bring it near the electronic box, as indicated.
Sasha / Sasha white:
✐
■ (
it rests against the respective frame.
Adjust its position, by lifting it as much as is needed to move it
outwards and close any openings between frame and roof.
Sasha / Sasha white: ✐
■ (
head to the hammam's mixing system.
Sasha / Sasha white: ✐
■ (
ble to the terminal indicated.
Sasha (Sauna / Hammam); Sasha white (Hammam)
✐
■ ( 25) Fix the roof to the walls and apply the cover panels us-
ing soft double-sided tape and heat resistant silicone.
Benches and duckboards
Sauna:
✐
26, details 1-2) Position the heater cover and proceed
■ (
with the positioning of the duckboards (wood) adjacent to the
side walls.
Sasha white: ✐
23W, detail 1-2)
Sasha white: ✐
23W, detail 3) Posi-
Sasha white: ✐
23W, detail 4) Con-
24, detail 1) Attach the shower head
24, detail 2-3) Unwind the sensor
24, detail 4) Position the roof so that
24, detail 5) Connect the shower
24, detail 6) Connect the sensor ca-
✐
■ ( 26, details 3-4-5) Position the highest bench against the side
wall and connect the light cable underneath the cable coming from
the wall, sealing the cable outlet with the foam rubber bushing.
(details 6-7) Finish positioning the duckboards and then posi-
tion the lower bench.
Hammam
:
✐
27 , details 1-2-3) Check that the drain pipe covers are
■ (
present; then position the tank under the spout and proceed
with the positioning of the duckboard adjacent to the side wall.
✐
27, details 4-5-6) Position the bench against the side wall
■ (
and connect the light cable underneath the cable coming from
the wall, sealing the cable outlet with the foam rubber bushing.
(detail 7) Position the second duckboard.
Installing panels
All models
✐
28) Connect the cables to the display, attaching them to
■ (
the wall.
✐
29, details 1-2-3) Thread the light cables in the corner
■ (
hole, connecting them to the electrical box cables indicated.
Thread the foam rubber cylinder to the cables and insert it into
the wall hole.
✐
29, detail 4) After having checked all connections, close
■ (
the equipment zone, by replacing its cover.
✐
■ ( 29, detail 5) Draw the back support towards the side wall
and install it in such a way that the fasteners at the back can be
inserted into those on the side wall.
NOTE: the sauna panels are made of wood.
✐
29, detail 6) Insert the covering panel between the base
■ (
wall and the back support and install it in such a way that the
fasteners at the back can be inserted into those on the side wall.
NOTE: the sauna panels are made of wood.
✐
29, detail 7) Position the lights behind the panels.
■ (
Installing the door glass
✐
30, detail 1-3) Insert the plastic rings in the upper and
■ (
lower holes in the glass.
✐
■ ( 30, detail 2-4) Assemble the lower and upper hinge, ap-
plying the plates from the inner side of the glass.
✐
30, detail 5-6) Fit the vertical sealant and move the glass-
■ (
door near the fixed one.
✐
30, details 7-8) If you have not already done so, attach the
■ (
lower support and insert the ball into the ball pin.
NOTE: with the HAMMAM, we recommend placing silicone in
the holes of the cover to which the hinge is attached.
21