Jacuzzi sasha Montageanweisung Seite 17

PLEASE READ THESE INSTRUCTIONS THOROUGHLY BE-
FORE PROCEEDING WITH INSTALLATION
Info
Before proceeding with installation, check that all prepara-
tory work has been completed; for details, please see the
relative pre-installation instructions.
Please refer to the "package identification" outlines, which feature
at the beginning of this present manual to view the contents of each
box/package and to allow for advanced preparation of what you
will require at the installation stage described.
m
GIVEN THE CONSIDERABLE WEIGHT OF SOME PARTS,
AND IN ORDER TO ENSURE CORRECT INSTALLATION,
SASHA MUST BE INSTALLED BY AT LEAST 3 PERSONS.
m
ATTENTION: in order to move the glass, ONLY use a
suitable suction lifter; the size should be suited to the
weight of the actual glass (75 kg). You must also use
suitable protective gloves.
Installing the base (frame and tank)
✐
■ ( 1-1a, detail1) Remove the sauna or hammam frame and
then remove the glazing beads.
✐
1-1a, details 2-3) Screw the supports to the frame, ad-
■ (
justing the corner supports to the specified measurement (also
check the spirit level).
NOTE: do not throw away the foam rubber bushings included in the
bag containing the supports! You will need them to seal the light
cable outlet holes (see the Chapter "Installing the side walls").
✐
■ ( 1-1a, detail 4) Position the frame according to the indicat-
ed measurements (in the instance of a wall mounted installation,
please also refer to the installation angle or the supporting wall).
Lower the other supports so that they rest completely on the
ground (if necessary, use shims).
NOTE: with the supports fully screwed in (example measure-
ment: 95 mm), the cornice (see the. "Accessories" chapter)
will come out approximately 5 mm from the ground; with
the supports "screwed in" to the maximum (example meas-
urement: 100 mm), the cornice will come out approximately
10 mm.
✐
■ ( 2) Position the support plates as indicated and attach
them to the cross bars.
✐
3, details 1-2- hammam) Arrange the drains in their
■ (
housings in the ground in such a way, so that, once the tanks are
rested on top, they will align with the holes on the actual tanks
themselves.
Then, connect the drains amongst themselves and to the drain-
age system.
NOTE: in the case of the hammam, the drain with rubber hose con-
nection (P) must be positioned on the left, as indicated.
✐
■ ( 4, details 1-2 - hammam) Remove the boiler drainage
pipe and connect it to the drain with the rubber hose connec-
tion (P) (do not leave the hose under the frame but ensure it is on
the external side of the frame).
✐
■ ( 4, details 3-4-5) Position the metal tank on the respec-
tive frame, caulk the indicated areas with a silicone sealant and
tighten the drainage pipes ring nuts, covering them with their
respective covers.
✐
4, detail 6 - hammam) Place a line of silicone sealant be-
■ (
tween the tank and the frame, along the entire perimeter so that
the space is sealed. You must achieve a continuous, even seam.
✐
■ ( 4, detail 7 - hammam) Assemble the equipotential termi-
nals, screw them to the frame and connect the building's equi-
potential circuit, then connect the supplied yellow-green cable
to the terminal (this cable will then be connected to the faston con-
nector on the mixer system).
Installing the base walls
Sauna walls
■
Sasha white:
✐
■ ( 5SW) Install the lower wall to the base frame so that:
- (detail1) the wood dowel is inserted into the frame. Subse-
quently, use a rubber mallet if necessary.
- (detail 2 ) Using the suction lifter, draw in the upper wall and
install it as per the instructions described above.
Sasha / Sasha white:
✐
5S, details 1-2) In the instance where an automatic water
- (
filling device (SC) is installed, connect the supply pipe to the wall
connection and allow it to pass through the hole at the wall base.
✐
5S, detail 3) In the instance where a cable radio system is
- (
present, connect it to the electrical box, as indicated.
NOTE: if, on the other hand, an audio kit (optional) is present, refer
to the audio kit documentation.
NOTE: The audio system (cable radio system or optional audio kit)
can be installed in the compartment of any of the walls .
✐
- ( 5S, detail 4) Where present, connect the building alarm
system to the indicated terminals.
NOTE: the terminals to which you must connect, are normally-open (NO)
contacts powered by a relay, which can be powered to both 220/240 V
and low voltage, but with maximum power absorption equal to 5 A.
✐
5S, detail 5) Unroll the temperature sensor (SO) cable and
- (
allow it to pass through the grooves (the highest ones) located
at the wall end.
✐
5S, detail 5) Unwind the display (1) cable and allow it to
- (
pass via these same grooves.
✐
- ( 5S, detail 6) Thread the bench light cable (6) through the
lower grooves and route it towards the outside.
17