Oregon Scientific RRM612P Bedienungsanleitung

Smart Projection Clock with Mirror
Projector and LED Display
Model: RRM612P / RRM612PU /
RRM612PA
USER MANUAL
EN
OVERVIEW
INNER VIEW
6
5
1. FOCUS wheel: adjust projection focus
2. ALARM ON/OFF slide switch: enable or disable alarm
3. SLEEP: activate sleep timer
4. 1, 2, 3, 4: preset radio stations
5. RADIO ON/VOL : turn on radio; increase radio
volume
6. RADIO OFF/VOL
: turn off radio; decrease radio
volume
BOTTOM VIEW
1
9
8
7
1. SNOOZE buttons: snooze alarm; turn on projection
increase value during setting; increase
2. UP/TUNE +:
frequency during radio scan
3. DOWN/TUNE -: decrease value during setting; decrease
frequency during radio scan
4. Battery compartment
RESET: reset unit to default settings
5.
6. RCC CLOCK ON/OFF slide switch: enable or disable
clock signal reception
7. PROJECTION ON/OFF slide switch: enable or disable
projection
8. ALARM: set alarm
9. CLOCK: set clock
LED DISPLAY
1 2 3 4 5 6 7 8
10 9
1. Clock signal reception indicator
2. AM/PM indicator
3. Alarm icon
4. Sleep timer icon
5. Melody icon
6. Radio icon
7. Volume indicator
8. Low battery indicator
9. Time with hour and minute
10. Time zone indicator
BACK VIEW
D C 6 V
1. Power adaptor
GETTING STARTED
The product should be powered by the AC/DC adaptor. Plug
the adaptor into socket. Make sure it is not obstructed and is
easily accessible to the unit.
To completely disconnect from power, the adaptor should be
disconnected from the main unit.
NOTE
The main unit and adaptor should not be exposed to
wet conditions. No objects filled with liquid, such as vases,
should be placed on the main unit and adaptor.
Battery serves only as memory backup.
1. Remove the battery compartment cover.
2. Insert the battery, matching the polarities.
NOTE
Batteries should not be exposed to excessive heat
such as sunshine or fire.
indicates battery is low.
1
CLOCK
CLOCK RECEPTION
This product is designed to synchronize its clock automatically
2
with a clock signal.
3
RRM612P:
4
EU: DCF-77 signal: within 1500 km (932 miles) of Frankfurt,
Germany.
RRM612PU:
UK: MSF-60 signal: within 1500 km (932 miles) of Anthorn,
England.
RRM612PA:
WWVB-60 signal: within 3200 km (2000 miles) of Fort
Collins, Colorado.
To enable / disable clock signal reception:
Switch RCC CLOCK ON/OFF slide switch to ON to enable
or OFF to disable clock signal reception.
When clock signal reception is enabled (RCC CLOCK
ON/OFF slide switch is ON), reception will occur regularly
at 01:00, 02:00 and 03:00, or 3 minutes after every reset
of unit. During reception, display will be temporarily off and
only a flashing will be shown. Display will resume after
the reception, or upon pressing of any key, display will be
temporarily on for 10 seconds.
2
3
Clock signal reception indicator:
4
SUCCESSFUL RECEPTION FAILED RECEPTION
5
6 NOTE
•
Reception takes 2-10 minutes. If the signal is weak, reception
will end and time display will resume. Place your unit next to
a window for stronger reception.
• During reception, pressing any button or turning on the radio
will stop the reception temporarily. Reception will resume if
no more button is pressed after 10 seconds or the radio is
turned off.
• If the radio is playing during reception time, reception will not
occur.
MANUALLY SET CLOCK
1. Press and hold CLOCK.
2. Press UP/TUNE + or DOWN/TUNE - to increase or
decrease values.
3. Press CLOCK to confirm.
4. The settings order is: time zone, 12/24 hr format, hour
and minute.
RRM612P / RRM612PU: Time zone sets the clock +/-
23 hours from the received clock signal time. If you have
disabled the clock signal reception, do not set a value for
time zone.
RRM612PA: Select the time zone: (0) Pacific, (+1) Mountain,
(+2) Central or (+3) Eastern.
PROJECTION
IMPORTANT
If projection is illuminated, do not look directly
into the projector or on the reflection from the mirror.
• To enable continuous projection:
Slide PROJECTION ON/OFF slide switch to ON and
open the top cover.
•
To focus image:
Turn FOCUS wheel.
• To disable projection:
Slide PROJECTION ON/OFF slide switch to OFF. But,
if the top cover is opened, pressing SNOOZE can turn
on the projection for 5 seconds.
ALARM
To set alarm:
1. Slide ALARM ON/OFF slide switch to ON.
2. Press and hold ALARM.
3. Press UP/TUNE + or DOWN/TUNE - to set values for
hour and minute.
4. The settings order is: hour, minute, Melody alarm or
Radio alarm.
• If Melody alarm is selected, press UP/TUNE + or DOWN/
TUNE - to select Melody 1 / Melody 2 / Melody 3 /
buzzer.
•
If Radio alarm is selected, press UP/TUNE + or DOWN/
TUNE - to select radio station and press ALARM to
confirm, then press UP/TUNE + or DOWN/TUNE - to
adjust the volume.
5. Press ALARM to confirm. indicates alarm is on.
To activate / deactivate alarm:
Press ALARM.
1
To display alarm time:
Press ALARM. After 10 seconds, the display will resume to
clock or radio.
To silence alarm:
•
Press SNOOZE to silence it for 8 minutes.
OR
• Press any other button to turn the alarm off and activate it
again after 24 hours.
FM RADIO
To play the radio:
1. Press and hold RADIO ON/VOL
2. Press UP/TUNE + / DOWN/TUNE - to select radio
frequency (press and hold to enable auto-search for
an available frequency); or press 1, 2, 3 or 4 if radio
stations are saved.
To save a radio station:
Press and hold 1, 2, 3 or 4 while on a frequency. A total of 4
stations can be stored.
To adjust radio volume:
Press repeatedly RADIO ON/VOL
RADIO OFF/VOL
to decrease volume.
To turn off radio:
Press and hold RADIO OFF/VOL
RADIO SLEEP TIMER
The radio is equipped with a countdown sleep timer that can
be set to switch the radio off after up to 120 minutes.
1. Press SLEEP to activate sleep timer. The radio turns on
with the previous setting (radio frequency, volume and
timer).
2. To change the sleep timer setting (120, 90, 60, 45, 30,
15, 0), press SLEEP. The sleep timer setting will be
automatically activated.
NOTE
If no button is pressed after 10 seconds, the unit will
resume clock display.
RESET
Press RESET to return to the default settings.
PRECAUTIONS
Do not subject the unit to excessive force, shock, dust,
•
temperature or humidity.
• Do not cover the ventilation holes with any items such
as newspapers, curtains etc.
Do not immerse the unit in water. If you spill liquid over
•
it, dry it immediately with a soft, lint-free cloth.
Do not clean the unit with abrasive or corrosive
•
materials.
• Do not tamper with the unit's internal components. This
-
invalidates the warranty.
• Only use fresh batteries. Do not mix new and old
batteries.
Images shown in this manual may differ from the actual
•
display.
When disposing of this product, ensure it is collected
•
separately for special treatment.
• Placement of this product on certain types of wood
may result in damage to its finish for which Oregon
Scientific will not be responsible. Consult the furniture
manufacturer's care instructions for information.
The contents of this manual may not be reproduced
•
without the permission of the manufacturer.
Do not dispose old batteries as unsorted municipal
•
waste. Collection of such waste separately for special
treatment is necessary.
• Please note that some units are equipped with a
battery safety strip. Remove the strip from the battery
compartment before first use.
NOTE
The technical specifications for this product and the
contents of the user manual are subject to change without
notice.
NOTE Features and accessories will not be available in all
countries. For more information, please contact your local
retailer.
SPECIFICATIONS
TYPE DESCRIPTION
100 x 100 x 100 mm
L x W x H
(3.94 x 3.94 x 3.94 in)
Weight 460 g (16.2 oz) without battery
Preset FM
radio memory 4
stations
• User-selectable 120-minute
radio alarm or 2-minute
Alarm
melody or buzzer alarm
• 8-minute snooze
• 1 x CR2032 battery (for backup)
Power
• DC 6V 500mA adaptor
ABOUT OREGON SCIENTIFIC
Visit our website (www.oregonscientific.com) to learn more
about Oregon Scientific products. If you're in the US and
would like to contact our Customer Care department directly,
please visit:
www2.oregonscientific.com/service/support
For international inquiries, please visit:
www2.oregonscientific.com/about/international
EU-DECLARATION OF CONFORMITY
Hereby, Oregon Scientific, declares that this Smart Projection
Clock with Mirror Projector and LED Display (model:
RRM612P / RRM612PU / RRM612PA) is in compliance with
the essential requirements and other relevant provisions
of Directive 1999/5/EC. A copy of the signed and dated
Declaration of Conformity is available on request via our
Oregon Scientific Customer Service.
COUNTRIES RTTE APPROVED COMPLIED
All EU countries, Switzerland CH
FCC STATEMENT
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) This
device must accept any interference received, including
interference that may cause undesired operation.
WARNING
Changes or modifications not expressly
approved by the party responsible for compliance could void
.
the user's authority to operate the equipment.
NOTE This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee
to increase or
that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
•
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio / TV technician
for help.
DECLARATION OF CONFORMITY
The following information is not to be used as contact
for support or sales. Please visit our website at www2.
oregonscientific.com/service for all enquiries.
We
Name: Oregon Scientific, Inc.
Address: 19861 SW 95
Oregon 97062 USA
Telephone No.: 1-800-853-8883
declare that the product
Product No.: RRM612P / RRM612PU /
RRM612PA
Product Name: Smart Projection Clock with
Mirror Projector and LED Display
Manufacturer: IDT Technology Limited
Address: Block C, 9/F, Kaiser Estate,
Phase 1,41 Man Yue St.,
Hung Hom, Kowloon,
Hong Kong
is in conformity with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: 1) This device may not
cause harmful interference. 2) This device must accept any
interference received, including interference that may cause
undesired operation.
N
and Norway
Orolog
Mo
IT
PANORA
VISTA IN
6
5
1. Rote
fuoco
2. Leve
disat
3. SLE
4. 1, 2,
5. RAD
di au
6. RAD
di dim
VISTA IN
Ave.,Tualatin,
th
9
8
7
1. Tast
proie
2. UP/T
l'imp
ricer
3. DOW
l'imp
ricer
4. Vano
5. RES
dell'u
6. Leve
disat
7. Leve
disat
8. ALA
9. CLO
VISTA F
1. Indic
2. Indic
3. Icona
4. Icona
5. Icona
6. Icona
7. Indic
8. Indic
9. Ora
10. Indic
VISTA P
1. Ingre