Herunterladen Inhalt Inhalt Diese Seite drucken

IBM P260 Bedienungsanleitung Seite 27

Color monitor
Vorschau ausblenden Andere Handbücher für P260:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 52
Symptom
Screen image is not centered
or sized properly
Edges of the image are
curved
White lines show red or blue
shadows at edges
Picture is fuzzy
Picture bounces or has wavy
oscillations
Picture is flickering
Picture appears to be
ghosting
Wavy or elliptical (moire)
pattern is visible
COLOR RETURN function does
not operate
COLOR
EASY
EXPERT
s
R
5 0 0 0 K
6 5 0 0 K
9 3 0 K
5 0
COLOR
RE TURN
AVA I L AB L E
A F T ER WARM UP
Two fine horizontal lines
(wires) are visible
Hum is heard right after the
power is turned on
• If the problem persists, call the IBM HelpCenter.
In the US. call 1-800-772-2227
In Canada call 1-800-565-3344
• Note the model name and the serial number of your monitor. Also note the make and name of your computer and graphic
board.
Check these items
• Press the
button (page 5).
• Adjust the size or centering (page 7).
Some video modes do not fill the screen to the edges. This problem tends to occur with
certain graphic boards.
• Adjust the geometry (page 8).
• Adjust the convergence (page 9).
• Adjust the contrast and brightness (page 6).
• Degauss the monitor (page 13).
If you place equipment which generates a magnetic field, such as a loudspeaker, near
the monitor, or you change the direction of the monitor, color may lose uniformity.
The degauss function demagnetizes the metal frame of the CRT to obtain a neutral
field for uniform color reproduction. If a second degauss cycle is needed, allow a
minimum interval of 20 minutes for the best result.
• If red or blue shadows appear along the edges of images, adjust the convergence
(page 9).
• If CANCEL MOIRE is ON, the picture may become fuzzy. Decrease the moire
cancellation effect or set CANCEL MOIRE to OFF (page 10).
• Isolate and eliminate any potential sources of electric or magnetic fields. Common
causes for this symptom are electric fans, fluorescent lighting, or laser printers.
• If you have another monitor close to this monitor, increase the distance between them
to reduce the interference.
• Try plugging the monitor into a different AC outlet, preferably on a different circuit.
• Try the monitor on a different computer in a different room.
• Set the refresh rate on the computer to obtain the best possible picture by referring to
your computer's manual.
• Eliminate the use of video cable extensions and/or video switch boxes if this symptom
occurs. Excessive cable length or a weak connection can produce this symptom.
• Set CANCEL MOIRE to ON and adjust the degree of moire cancellation until the
moire is at a minimum (page 10).
• Due to the relationship between resolution, monitor dot pitch and the pitch of some
image patterns, certain screen backgrounds sometimes show moire. Change your
desktop pattern.
• Before using this function, the monitor must be in normal operation mode (green
power indicator on) for at least 30 minutes. For more information on using the COLOR
RETURN function, see page 12.
• Adjust the computer's power saving settings to keep the monitor in normal operation
G
B
mode for more than 30 minutes.
0
• The monitor may gradually lose its ability to perform this function due to the natural
0
0
K
aging of the picture tube.
• These wires stabilize the vertically striped aperture grille (page 15). This aperture grille
allows more light to pass through to the screen giving the Trinitron CRT more color
and brightness.
• When the power is turned on, the auto-degauss cycle is activated. While the auto-
degauss cycle is activated, a hum may be heard. The same hum is heard when the
monitor is manually degaussed. This is not a malfunction.
Getting Started
Additional Information
Additional Information
EN
19

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis