Campingaz Camp Bistro Stopgaz Bedienungsanleitung Seite 9

Lighting the burner (with STOPGAZ™ flame guard)
the equipment is fitted with a piezo-electric lighter
connected to an ignition electrode (6).
- turn the control knob (1) anti-clockwise until you hear
a click ( ) indicating a spark (fig. 7). hold the knob in
this position for a few seconds to prime the flame guard
thermocouple. if the equipment does not light, turn
the control knob to position "l" (fig. 9) and start the
operation again.
- if the equipment still does not light after three attempts,
turn the control knob to position "l" and check that the
cartridge contains gas (sound of liquid sloshing when
shaken) before starting the previous steps again. (if the
cartridge is empty, refer to paragraph D - Changing the
cartridge).
Cooking
Position the pan on the arms centred over the burner and
adjust the gas flow so that the flames do not burn higher
than the pan.
the size of the flame can be regulated by turning the
ignition knob (2) between the full flow position
( ) and medium flow position (
Extinguishing
turn the ignition knob (1) clockwise to "l" position (fig. 9).
D - CHANGING THE CARTRIDGE
the cartridge may be removed even if it is not empty.
Once your equipment has fully cooled:
- Check that the gas inlet is fully closed by turning the
control knob (1) clockwise to the "l" position (fig. 9) and
that the burner (5) is extinguished.
- Disconnect the cartridge by putting the lever (2) in the
"unLoCK" position.
- open the cartridge compartment (3) and remove the
cartridge by lifting it from behind.
- never throw away a cartridge which is not completely
empty, (check there is no liquid in the cartridge by shaking
it).
- make sure that no food has dropped into and thus
obstructs the equipment regulator internal housing (fig.
4) before installing a new cartridge.
- Check that the seal is present and in good condition (fig. 4)
- Put in a new cartridge by following the instructions in
paragraph "B - PRePaRation foR oPeRation - installing
a CamPingaz® cartridge CP250/ CP250 SP".
Caution: if the cartridge is replaced while the appliance
is in use, do not touch the hot surfaces of the appliance
(burner, saucepan holder, plate...).
Caution: Some fuel may remain in the gas cock after the
unit has been turned off. for your safety, with the cartridge
lever (2) in "unLoCK" position, turn ignition knob (1) to ( )
position to burn off any remaining fuel.
E - SAFETY DEvICE
Do not use an appliance which is leaking, damaged, or
which does not operate properly.
if the gas pressure in the cartridge is too high (for instance
overheating due to too large a surface on the cooking grill)
a built-in device disconnects the cartridge and the lever
(2) returns to "unLoCK". in this case, you need to remove
the cartridge and let it cool down (run it under water, for
example) before reusing it or use a new cartridge following
the instructions in Section "D - C
the unit will not operate until the gas pressure of the
cartridge returns back to the normal stove.
).
".
hanging the Cartridge
HOW TO RESET SAFETY DEvICE
- turn the ignition knob (1) to the "l" position and raise
cartridge lever (2) up to the "unLoCK" position.
- Remove the gas cartridge.
- turn the ignition knob to the ( ) position to release
excess gas in the gas cock.
- after 5 minutes, turn the ignition knob to the "l" position.
- make sure the ignition knob is "l" and reset safety device
by:
a) Pushing the cartridge lever down to "LoCK" position,
and then
b) Pushing the cartridge lever up to "unLoCK" position.
- Replace a new cartridge or a cooled down cartridge.
- Repeat the ignition procedure.
if the temperature in the cartridge is high initially, fuel will
not emerge even though the cartridge is installed in the
stove. this is due to the operation of the safety device. it is
not out of order.
STOPGAZ™ flame guard
the thermocouple placed in the flame (9) controls a valve
which automatically cuts off the gas intake to the burner
when this is extinguished (air draught or overflowing liquid,
for example). to relight it, follow the steps in paragraph C -
Lighting the burner (with StoPgaz™ flame guard).
F - CLEANING AND STORAGE
In case of burn back (ignition under the burner
cap) switch the product off, allow it to cool down
(approximately five minutes), then reignite the
appliance. If the problem of burn back persists, then
please contact your local Campingaz® representative.
Once your equipment has fully cooled:
1 - Cleaning
main equipment
- Clean the equipment having removed the cartridge.
- Clean the pan support (4) and the cartridge exterior and
cover (3) with warm water, then dry with a cloth.
Burner (5)
a dirty burner will clog the holes of the flame.
Clean the flame holes of burner head with a metal brush
ignition Plug
lf it is wet, ignition will not be made. make sure any water
is removed, and dry with a cloth.
2 - Storage and transportation
- Check that the lever (2) is in the unLoCK position (fig. 10).
- always remove the gas cartridge from the product
during storage or transportation of the appliance.
- Store the equipment and the cartridge in a cool, dry and
well-ventilated area, out of reach of children. never store
in a basement or cellar.
9
GB