Maintenance - SIOUX SDR5P-Serie Bedienungsanleitung Und Teileliste

AIR SUPPLY
The efficiency and life of this tool depend on the proper supply of clean, dry air at a maximum of 90 PSI. The use of an air line filter, pressure regulator,
and lubricator is recommended. Before connecting to tools, blow out the air line to remove water and dirt that may have accumulated.
HOSE AND HOSE CONNECTIONS
The air supply hose recommended is 3/8" (10mm) I.D. If an extension hose is necessary, use 1/2" (13mm) ID hose with couplings not less than 3/8" (10mm) I.D.
LUBRICATION
For maximum performance and tool life, an air line lubricator, set to deliver 2 drops per minute, is recommended. SIOUX No. 288 Air Motor Oil is recommended.
If an airline lubrication is not used, it is recommended that the tool be oiled daily before use to improve performance. Add 2-4 drops of air motor oil and
run the tool for 10-20 seconds to distribute oil through the tool. Lubricate the gears through the grease fitting with Sioux 1232A grease after 100 hours of
operation.

MAINTENANCE

Water, dust and other airline contaminants can cause rust and vane sticking. For long periods between tool use, flush the tool with a few drops of oil and
run for 10 seconds. This will help remove contaminants and reduce the formation of rust. Check the speed of the tool regularly by placing a contact type
tachometer to the chuck. In addition, always check the speed and do a simple vibration check after any servicing. If the tool exceeds the rated speed or
vibrates excessively discontinue use and contact an Authorized Sioux Service Center. Avoid exposure to hazardous substances deposited on the tool.
Speed
Catalog No.
(RPM)
SDR5P5N2
SDR5P7N2
SDR5P8N2
SDR5P9N2
SDR5P10N2 1000
SDR5P12N2 1200
SDR5P15N2 1500
SDR5P18N2 1800
SDR5P22N2 2200
SDR5P26N2 2600
SDR5P30N2 3000
SDR5P36N2 3600
SDR5P43N2 4300
SDR5P50N2 5000
SDR5P60N2 6000
SDR5P230N2 TBD
SDR5P3R2
SDR5P4R2
SDR5P5R2
SDR5P6R2
SDR5P7R2
SDR5P8R2
SDR5P10R2 1000
SDR5P12R2 1200
SDR5P16R2 1600
SDR5P18R2 1800
SDR5P20R2 2000
SDR5P24R2 2400
SDR5P30R2 3000
SDR5P33R2 3300
SDR5P40R2 4000
Form ZCE834
Disconnect tool from air supply before installing or removing drill bit or making any adjustments
NOISE AND VIBRATION READINGS
Weight
lbs. kg.
500 1.5 0.68
700 1.5 0.68
800 1.5 0.68
900 1.5 0.68
1.5 0.68
1.5 0.68
1.5 0.68
1.5 0.68
1.5 0.68
1.5 0.68
1.5 0.68
1.5 0.68
1.5 0.68
1.5 0.68
1.5 0.68
1.5 0.68
300 1.7 0.68
400 1.7 0.68
500 1.7 0.68
600 1.7 0.68
700 1.7 0.68
800 1.7 0.68
1.7 0.68
1.7 0.68
1.7 0.68
1.7 0.68
1.7 0.68
1.7 0.68
1.7 0.68
1.7 0.68
1.7 0.68
WARNING
Noise (Tested in accordance with ISO
Chuck Capacity
Standard 15744)
Sound Sound
in. mm. Pressure Power
(dBA) (dBA)
0.5 HP Non-reversible
0.25 6.5 84.7
0.25 6.5 85.4
0.25 6.5 84.5
0.25 6.5 86.3
0.25 6.5 TBD
0.25 6.5 TBD
0.25 6.5 TBD
0.25 6.5 TBD
0.25 6.5 TBD
0.25 6.5 86.2
0.25 6.5 82.3
0.25 6.5 86.5
0.25 6.5 85.0
0.25 6.5 87.2
0.25 6.5 TBD
0.25 6.5 86.1
0.5 HP Reversible
0.25 6.5 85.9
0.25 6.5 86.2
0.25 6.5 86
0.25 6.5 87.2
0.25 TBD TBD
0.25 TBD TBD
0.25 TBD TBD
0.25 TBD TBD
0.25 TBD TBD
0.25 6.5 85.7
0.25 6.5 85.6
0.25 6.5 86.6
0.25 6.5 86.2
0.25 TBD 84.9
0.25 TBD TBD
3
Vibration (Tested in
accordance with ISO
Standard 28927-5:2009)
Uncertainty Vibration
(dBA) (m/s )
2
96.3 3 0.44
97 3 0.63
96.1 3 0.51
97.9 3 0.67
TBD 3 TBD
TBD 3 TBD
TBD 3 TBD
TBD 3 TBD
TBD 3 TBD
97.8 3 0.46
93.9 3 1.34
98.1 3 1.71
96.6 3 0.42
98.8 3 1.65
TBD 3 TBD
97.7 3 1.58
97.5 3 0.48
97.8 3 0.51
97.6 3 0.45
98.8 3 0.41
TBD 3 TBD
TBD 3 TBD
TBD 3 TBD
TBD 3 TBD
TBD 3 TBD
97.3 3 0.62
97.2 3 1.44
98.3 3 1.94
97.8 3 0.34
96.6 3 0.85
TBD 3 TBD
Date
Uncertainty, K
(m/s )
2
0.04
0.09
0.05
0.11
TBD
TBD
TBD
TBD
TBD
0.04
0.08
0.17
0.03
0.20
TBD
0.04
0.04
0.03
0.03
0.02
TBD
TBD
TBD
TBD
TBD
0.02
0.07
0.23
0.01
0.08
TBD
2019December10/F