Maintenance - SIOUX A-Serie Bedienungsanleitung Und Teileliste

LUBRICATION
For maximum performance and tool life, an air line lubricator, set to deliver 2 drops per minute, is recommended. SIOUX No. 288 Air Motor Oil is recommended.
If an airline lubrication is not used, it is recommended that the tool be oiled daily before use to improve performance. Add 2-4 drops of air motor oil and run the
tool for 10-20 seconds to distribute oil through the tool. Lubricate the gears through the grease fitting with Sioux 1232A grease after 100 hours of operation.

MAINTENANCE

Water, dust and other airline contaminants can cause rust and vane sticking. For long periods between tool use, flush the tool with a few drops of oil and
run for 10 seconds. This will help remove contaminants and reduce the formation of rust. Check the speed of the tool regularly by placing a contact type
tachometer to the chuck. In addition, always check the speed and do a simple vibration check after any servicing. If the tool exceeds the rated speed or
vibrates excessively discontinue use and contact an Authorized Sioux Service Center. Avoid exposure to hazardous substances deposited on the tool.
Speed
Catalog No.
(RPM)
SDR4P5N2 500
SDR4P7N2 700
SDR4P8N2 800
SDR4P9N2 900
SDR4P10N2 1000
SDR4P12N2 1200
SDR4P15N2 1500
SDR4P18N2 1800
SDR4P22N2 2200
SDR4P26N2 2600
SDR4P30N2 3000
SDR4P36N2 3600
SDR4P43N2 4300
SDR4P50N2 5000
SDR4P60N2 6000
SDR4S22N2 2200
SDR4S26N2 2600
SDR4S30N2 3000
SDR4S36N2 3600
SDR4S43N2 4300
SDR4S50N2 5000
SDR4S60N2 6000
SDR4P3R2 300
SDR4P4R2 400
SDR4P5R2 500
SDR4P6R2 600
SDR4P7R2 700
SDR4P8R2 800
SDR4P10R2 1000
SDR4P12R2 1200
SDR4P16R2 1600
SDR4P18R2 1800
SDR4P20R2 2000
SDR4P24R2 2400
SDR4P30R2 3000
SDR4P33R2 3300
SDR4P40R2 4000
SDR4P3R2RR 300
SDR4P4R2RR 400
SDR4P5R2RR 500
SDR4P6R2RR 600
SDR4P7R2RR 700
SDR4P8R2RR 800
SDR4P10R2RR 1000
SDR4P12R2RR 1200
SDR4P16R2RR 1600
SDR4P18R2RR 1800
SDR4P20R2RR 2000
SDR4P24R2RR 2400
SDR4P30R2RR 3000
SDR4P33R2RR 3300
SDR4P40R2RR 4000
Form ZCE840
Disconnect tool from air supply before installing or removing drill bit or making any adjustments
NOISE AND VIBRATION READINGS
Weight Chuck Capacity
lbs. kg. in.
1.5 0.68 0.25
1.5 0.68 0.25
1.5 0.68 0.25
1.5 0.68 0.25
1.5 0.68 0.25
1.5 0.68 0.25
1.5 0.68 0.25
1.5 0.68 0.25
1.5 0.68 0.25
1.5 0.68 0.25
1.5 0.68 0.25
1.5 0.68 0.25
1.5 0.68 0.25
1.5 0.68 0.25
1.5 0.68 0.25
1.5 0.68 0.25
1.5 0.68 0.25
1.5 0.68 0.25
1.5 0.68 0.25
1.5 0.68 0.25
1.5 0.68 0.25
1.5 0.68 0.25
1.5 0.68 0.25
1.5 0.68 0.25
1.5 0.68 0.25
1.5 0.68 0.25
1.5 0.68 0.25
1.5 0.68 0.25
1.5 0.68 0.25
1.5 0.68 0.25
1.5 0.68 0.25
1.5 0.68 0.25
1.5 0.68 0.25
1.5 0.68 0.25
1.5 0.68 0.25
1.5 0.68 0.25
1.5 0.68 0.25
1.5 0.68 0.25
1.5 0.68 0.25
1.5 0.68 0.25
1.5 0.68 0.25
1.5 0.68 0.25
1.5 0.68 0.25
1.5 0.68 0.25
1.5 0.68 0.25
1.5 0.68 0.25
1.5 0.68 0.25
1.5 0.68 0.25
1.5 0.68 0.25
1.5 0.68 0.25
1.5 0.68 0.25
1.5 0.68 0.25
WARNING
Noise (Tested in accordance with ISO
Standard 15744)
Sound Sound
mm. Pressure Power
(dBA) (dBA)
Non-Reversing
6.5 74.9 86.5
6.5 74.0 85.7
6.5 75.0 86.6
6.5 77.9 89.5
6.5 TBD TBD
6.5 TBD TBD
6.5 TBD TBD
6.5 TBD TBD
6.5 72.4 84.1
6.5 78.9 90.5
6.5 70.9 82.5
6.5 79.0 90.6
6.5 79.5 91.1
6.5 69.1 80.7
6.5 70.1 81.7
6.5 TBD TBD
6.5 TBD TBD
6.5 TBD TBD
6.5 TBD TBD
6.5 TBD TBD
6.5 TBD TBD
6.5 TBD TBD
Reversing
6.5 79.5 91.1
6.5 78.7 90.3
6.5 78.7 90.3
6.5 74.9 86.5
6.5 TBD TBD
6.5 TBD TBD
6.5 TBD TBD
6.5 TBD TBD
6.5 TBD TBD
6.5 77.5 89.2
6.5 76.4 88
6.5 78.9 90.5
6.5 77.1 88.7
6.5 79.0 90.6
6.5 TBD TBD
6.5 TBD TBD
6.5 TBD TBD
6.5 TBD TBD
6.5 TBD TBD
6.5 TBD TBD
6.5 TBD TBD
6.5 TBD TBD
6.5 TBD TBD
6.5 TBD TBD
6.5 TBD TBD
6.5 75.5 87.2
6.5 TBD TBD
6.5 76.2 87.9
6.5 TBD TBD
6.5 TBD TBD
3
Vibration (Tested in
accordance with ISO
Standard 28927-5:2009)
Uncertainty Vibration Uncertainty, K
(dBA) (m/s ) (m/s
2
3 0.45 0.06
3 0.45 0.06
3 0.42 0.02
3 0.77 0.09
3 TBD TBD
3 TBD TBD
3 TBD TBD
3 TBD TBD
3 1.29 0.16
3 1.24 0.1
3 1.33 0.15
3 1.7 0.13
3 0.8 0.07
3 1.08 0.08
3 1.06 0.17
3 TBD TBD
3 TBD TBD
3 TBD TBD
3 TBD TBD
3 TBD TBD
3 TBD TBD
3 TBD TBD
3 0.39 0.05
3 0.45 0.06
3 0.37 0.04
3 0.39 0.04
3 TBD TBD
3 TBD TBD
3 TBD TBD
3 TBD TBD
3 TBD TBD
3 2.68 0.2
3 1.86 0.19
3 2.62 0.16
3 2.46 0.14
3 0.95 0.06
3 TBD TBD
3 TBD TBD
3 TBD TBD
3 TBD TBD
3 TBD TBD
3 TBD TBD
3 TBD TBD
3 TBD TBD
3 TBD TBD
3 TBD TBD
3 TBD TBD
3 1.00 0.1
3 TBD TBD
3 1.17 0.1
3 TBD TBD
3 TBD TBD
2020January24/F
Date
)
2