Connecting The Hedge Trimmer Gb; Instructions For Use Of The Equipment Gb; Adjusting The Turning Handle Gb - Ikra HS 6070 Pro Gebrauchsanweisung

seek a practical demonstration from an
expert.
- Always ensure that all protective devices
and handles are properly fitted. Never at-
tempt to use an incomplete machine.
- Never try to use an incomplete tool or a
tool that has been modified in a way that
has not been approved.
- Familiarize yourself with the working area
and pay attention to possible dangers
which you might not be able to hear due to
the noise of the machine.
- Avoid to use the hedge-trimmer in poor
weather conditions, especially if there is a
risk of a thunderstorm.
-
-
Connecting the hedge trimmer
The machine can only be used on single-phase AC
current. It is double-insulated in accordance with Class
II VDE 0700 and EEC 20. Before using the trimmer, en-
sure that the mains voltage is the same as the operating
voltage shown on the rating plate.
Wires of extension cord must have the following mini-
mum cross sectional area: 1,5 mm
• Push the button X (Figure 1) to swivel the cable brack-
et outwards.
• For the purpose of strain relief, put a loop of the exten-
sion cord through the opening in the handle. Push the
button to swivel the cable bracket inwards again.
• When your work is finished, push the button X (Figure
1) to swivel the cable bracket outwards and pull out
the extension cord.
Instructions for use of the equipment
Do not use the trimmer in rain or for cutting wet hedges!
Check the hedge trimmer flex and its connections
before each and every use for visible signs of damage
(disconnect the power plug)! Do not use a faulty flex.
Gloves:
Protective gloves must be worn when using the hedge
trimmer.
Switching the hedge shears on/off
When switching the hedge shears on take a safe stand.
These hedge shears have a two-hand safety switch. To
switch the hedge trimmer on the bar switch in the handle
(A) must be pushed and the rotary switch of the handle
(B) must be rotated by 45° backward. To switch the de-
vice off let go of both switches. The motor already stops
if one of the two switches is released.
GB | Operating Instruction
)
(Fig. 1-2
2
(Fig. 3)
GB-6
Adjusting the turning handle
To facilitate your work the hedgetrimmer are equipped
with a turning rear handle that can be set in 3 different
positions (right, left, and normal). The purpose of this
mechanism is that especially for cutting in vertical direc-
tion the hedge shears can be held in their ergonomically
most favourable position whereby an early fatigue of the
user is avoided.
Please proceed as follows to change the position of the
handle:
Release switch (A). Pull back the locking pin (1 or 2)
(Fig. 3). The handle is now unlocked and can be turned
to the desired position (Fig. 4). In the desired end posi-
tion, the pin locks back into place and securing the han-
dle and avoiding an accidental change of the position.
For a more comfortable way of working the turning
handle can be set continuously, too. Press either the
red lock button 1 or 2 and keep it pushed. The hedge
trimmer can now comfortably be turned to all directions
while working.
To increase safety when operating the turn handle, the
trimmer drive shuts off in less that 0.1 seconds if either
the switch on the hand grip (A) or the red switch rail on
the turn handle (B) is released. This ensures that the
hedge trimmer can only be operated if both hands are
on the hand grips and at the same time both switches
are actuated. This effectively eliminates the risk of injury,
combined with the extremely short run-on time.
Maintenance
Always disconnect the plug from the power socket
before commencing any work on the machine.
Important: Always clean and oil the blades after pro-
longed use of the hedge trimmer. This will greatly affect
the life of the equipment. Damaged cutting units must
be properly repaired immediately. Clean the shearing
blades with a dry cloth or – in case of heavier dirt – with a
brush. Attention: Danger of injury! Oiling of the blades
should ideally be carried out using an environmentally
friendly lubricant (Fig. 6).
Sharpening of the blades
The blades generally do not need servicing and do not
require resharpening if used correctly. In order to pre-
vent injuries caused by the blades when not in use, the
sharpened cutting blade should be covered by the blade
cover. The blades cannot be sharpened by the user
without opening the equipment and the safety mecha-
nism. Resharpening of the blades can therefore only be
carried out at a specialist workshop.
Changing the blades
Only correct installation of the blades will guarantee
problem-free operation and function of the above
mentioned safety feature of the blades. Changing of
the blades should therefore only be carried out at a
specialist workshop.
(Fig. 3-5)