Specifications - Casals VSC65 Bedienungsanleitung

d Once you have finished using the appliance:
- Stop the appliance by releasing the on/off switch.
w
Maintenance and care
WARNING! Always unplug the machine before carrying
out work on it.
disc - Checking the saw blade: deposits of resin and glue
on the saw blade cause inefficient cutting. To avoid them,
ter, always clean the blade immediately after use.
ter - Inspect the mounting screws: regularly inspect all the
mounting screws and ensure they are firmly tightened.
and Should any screw be loose, tighten it immediately. Failure
to do so could put you at serious risk.
- Motor maintenance: always take the greatest care
an. over this and make sure that the motor winding is not
hine damaged and does not become wet with oil or water.
- The vents should always be kept clean and free of
obstacles.
e to - Clean the machine thoroughly after each use. Blast the
motor regularly with compressed air.
ps as - Check that the mains lead is in good condition. If it
is not, take it to an Official Service Centre to have it
replaced.
lector
dust Cleaning
- Disconnect the appliance from the mains and allow it
to cool before undertaking any cleaning task.
- Clean the electrical equipment and the mains
connection with a damp cloth and dry. DO NOT
and IMMERSE IN WATER OR ANY OTHER LIQUID.
nted - Clean the equipment with a damp cloth with a few
drops of washing-up liquid and then dry.
- Do not use solvents, or products with an acid or base
pH such as bleach, or abrasive products, for cleaning
. the appliance.
nd - Do not let water or any other liquid get into the air
vents to avoid damage to the inner parts of the
appliance.
- Never submerge the appliance in water or any other
ade in liquid or place it under running water.
uts. - If the appliance is not in good condition of cleanliness,
its surface may degrade and inexorably affect the
duration of the appliance's useful life and could
idth become unsafe to use.
- CAUTION: There is a risk of fire if the appliance's
cleaning is not done according to these instructions.
Supplies
r in - Always use original supplies, designed specifically
d, the for your appliance model.
- These supplies are available in specialist shops.
Anomalies and repair
- Take the appliance to an authorised technical support
service if a product damage or other problems arise. Do
not try to dismantle or repair without assistance, as this
may be dangerous.
- If the connection to the mains has been damaged, it
must be replaced and you should proceed as you would
in the case of damage.

Specifications:

- Rated power:
- Rated Voltage:
- Rated Frequency:
- No load Speed:
- Max Blade diameter:
- Max/min Blade width:
- Depth cut at 90º:
- Depth cut at 45º:
- Depth setting:
- Inclination setting:
- Weight:
- Sound Pressure level (LpA) =
- Sound Power level (LwA) =
- Inst. sound pressure level (LpCpeak) = 125dB(C), KpCpeak = 3dB
- Vibration =
- Not suitable for use in presence of flammable anaesthetic
mixture with air or with Oxygen or nitrous oxide
NB: These specifications are subject to change without
notice of purpose of improvement.
Measured sound level determined according EN60745.
The vibration emission level given in this information sheet
has been measured according EN60745 and may be
used to compare one tool with other. It may be used for a
preliminary assessment of exposure.
The vibration value during actual use of the power tool can
differ from the declared total value depending on the way
in which tool is used
For EU product versions and/or in case that it is
requested in your country:
Ecology and recyclability of the product
- The materials of which the packaging of this appliance
consists are included in a collection, classification and
recycling system. Should you wish to dispose of them,
VSC65
1200 W
230-240V~
50Hz
4500 rpm
Ø 185mm
2.8/2.5mm
65 mm
45mm
0-65mm
0-45º
3.5 Kg
97dB(A), KpA = 3dB
108dB(A), KWA = 3dB
3.5 m/s2, K= 1.5m/s2
7