Casals VSC65 Bedienungsanleitung Seite 6

soon as blade enters the material, the lower guard must
be released. For all other sawing, the lower guard should
operate automatically.
- Always observe that the lower guard is covering the
blade before placing saw down on bench or floor. An
unprotected, coasting blade will cause the saw to walk
backwards, cutting whatever is in its path. Be aware of the
time it takes for the blade to stop after switch is released.
Product description and Specifications
Description
A HM saw blade
B Spindle blocking button
C Mobile blade guard
D Saw blade setting disc
E Disc setting screw
F Depth setting wing nut
G Lateral stop setting wing nut
H Safety push button switch
I On-/off switch
J Angular cutting wing nut
K Cutting line guide
L
Sawdust extraction
M Lateral Stop
Instructions for use
Before use:
- Make sure that all the product's packaging has been
removed.
- Ensure that the voltage indicated on the rating label
matches the mains voltage before plugging in the
appliance.
- Prepare the appliance according to the function you
wish to use:
Fitting the disc
- Unplug the appliance from the mains before replacing
any accessory.
WARNING! : Always unplug the machine before carrying
out any work on it.
CAUTION: Do not use bent or cracked blades or high-
speed steel blades. Do not use saw blades that do
not conform to the specifications contained in these
instructions.
WARNING! Never press the blocking button B when
the machine is running. The shaft must have stopped
completely before the blocking button B is pressed.
6
1. Move the mobile guard (C) backwards and hold
it in place.
2. To loosen or tighten screw (E), block the screw
press by pushing block button (B).
3. Loosen the screw (E) and remove the setting
disc (D).
4. Fit the saw blade and tighten with the setting disc
(D) and the screw (E).
4.1 To adapt saw discs with a 30mm hole diameter,
first fit the washer that corresponds to the diameter
of the saw disc you are using, next the saw disc
and screw them into place with fastening disc D and
screw E.
5. Before fitting the new blade, make sure the
surfaces in contact with the setting discs are clean.
(The arrow printed on the fixed guard of the machine
indicates the cutting direction of the teeth).
6. Once the disc is fitted, check that the blocking
button (B) has returned to its original position due to
movement of the incorporated spring.
- In order to remove disc, follow the same steps as
indicated previously but in reverse order.
Dust extraction Assembly
- Always use the appliance with the dust collector
connected, inhaling dust is harmful to your health.
- Connect the vacuum aspirator suction tube to the dust
extraction adaptor (L)
Use:
Cutting depth setting
- To adjust the cutting depth, loosen the wing nut (F) and
move the base upwards or downwards. The scale printed
on the base indicates the cutting depth
Cutting angle setting
It can cut vertically and with an inclination of up to 45º.
The angle is adjusted by loosening the wing nut (J) and
according the scale printed on the base.
Cutting indication
The notch K is used as a cutting indication with the blade in
a vertical position or 45º. It is advisable to make test cuts.
Lateral stop adjustment
For parallel cutting, use the lateral stop (M). Cutting width
is adjusted with the scale or according to the plotting.
Tighten the wing nut (G) to work with the lateral stop.
- Connect the appliance to the mains.
- Press the locking button (H), and squeeze the trigger in
the on/off switch (I). When the on/off switch is released, the
machine stops.
Once
- Stop
Maint
WARN
out wo
- Che
on the
alway
- Insp
moun
Shoul
to do
- Moto
over t
dama
- The
obsta
- Clea
motor
- Che
is not,
replac
- Disc
to coo
- Clea
conne
IMME
- Clea
drops
- Do n
pH su
the ap
- Do
vents
applia
- Nev
liquid
- If the
its su
durat
becom
- CAU
clean
Supp
- Alwa
for yo
- The