Casals VSC65 Bedienungsanleitung Seite 3

English
Circular Saw
VSC65
Dear Customer,
Many thanks for trusting to Casals.
Thanks to its continuous effort, our innovation and the
strictest quality controls, Casals develops electric Power
Tools for the toughest jobs.
Read these ORIGINAL instructions carefully before
switching on the appliance and keep them for future ref-
erence. Failure to follow and observe these instructions
could lead to an accident.
GENERAL POWER TOOLS SAFETY WARNING
WARNING Read all safety warnings and all in-
structions. Failure to follow the warnings and instructions
may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference
The term "power tool" in the warnings refers to your main-
soperated (corded) power tool or battery-operated (cord-
less) power tool.
Work Area Safety
- Keep the working area clean and well lit. Cluttered and
dark areas invite accidents.
- Do not operate power tools in explosive atmo-
spheres, such as in the presence of flammable liquids,
gases or dust. Power tools create sparks which may ig-
nite the dust or fumes
- Keep children and bystanders away while operating
a power tool. Distractions can cause you to lose control
- CAUTION: In order to prevent overheating do not cover
the appliance.
- Ensure that neither the air access nor exit become either
totally or partially covered by drapery, clothing, etc., as this
increases the risk of fire.
Electric safety
- Power tool plugs must match the outlet. Never modify the
plug in any way. Do not use any adapter plugs with earthed
(grounded) power tools. Unmodified plugs and matching out-
lets will reduce risk of electric shock
- Avoid body contact with earthed or grounded surfaces,
such as pipes, radiators, ranges or refrigerators. There is
an increased risk of electric shock if your body is earthed or
grounded
- Do not expose power tools to rain or wet conditions. Water
entering a power tool will increase the risk of electric shock
- Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away
from heat, oil, sharp edges or moving parts. Damaged or
entangled cords increase the risk of electric shock
- When operating the power tool outdoors, use an extension
cord suitable for outdoor use. Use a cord suitable for outdoor
use reduces the risk of electric shock
- If operating a power tool in a damp location is unavoidable,
use a residual current device (RCD) protected supply. Use
of an RCD reduces the risk of electric shock
- Do not use the appliance if the cable or plug is damaged.
- Ensure that the voltage indicated on the rating label matches
the mains voltage before plugging in the appliance.
- Only use the appliance with the specific electric connector
provided.
- If any of the appliance casings breaks, immediately disconnect
the appliance from the mains to prevent the possibility of an
electric shock.
- Do not use the appliance if it has fallen on the floor, if there are
visible signs of damage or if it has a leak.
- CAUTION: Maintain the appliance dry.
- CAUTION: Do not use the appliance near water.
- Do not use the appliance with damp hands or feet, or when
barefooted.
- Do not wrap the power cord around the appliance.
- Do not clip or crease the power cord.
- Check the state of the power cord. Damaged or tangled cables
increase the risk of electric shock.
- Do not touch the plug with wet hands.
Personal safety
- Stay alert, Watch you are doing and use common sense
when operating a power tool. Do not use a power tool while
you are tired or under the influence of drugs, alcohol or
medication. A moment of inattention while operating power
tools may result in serious personal injury
- Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection used for appropri-
ate conditions will reduce personal injuries.
- Prevent unintentional starting. Ensure the switch is in the
off-position before connecting the power source and/or
battery pack, picking up or carrying the tool. Carrying power
tools with your finger on the switch or energizing power tools that
have the switch on invites accidents
- Remove any adjusting key or wrench before turning the
power tool on. A wrench or a key left attached to a rotating part
of the power tool may result in personal injury
- Do not overreach. Keep proper footing and balance at
all times. - This enables better control of the power tool in
unexpected situations
- Dress properly. Do not wear loose clothing or jewellery. Keep
your hair, clothing and gloves away from moving parts. Loose
3