Werbung
OTi QBM 20/220-240/500 NFC I | OTi QBM 30/220-240/700 NFC I | OTi QBM 40/220-240/1A0 NFC I
21)
Position
Input /PRI
24)
A or B
one cable
Input /PRI
26)
A and B
two cables
C
Output / SEC
D
Output / SEC
*Safety information for mains through wiring: Cable temperature in the cable clamp compartment de-
pends on cable type, ambient temperature and through wiring current. Therefore through wiring current
is limited. 2-wire connector for solid earthing conductors, e.g. WAGO 2273-202, is recommended.
Installing and operating information:
Connect only LED load type. LED module will be switched off when
output voltage is outside the voltage range given on the driver.
Wiring information (see fig. A):
Do not connect the outputs of two or more units. Output current
adjustment via software programming using Near Field Communica-
tion (NFC) in mains off mode only. Unit is permanently damaged if
mains is applied to the terminals 21/22. Lines 21/22 max. 2 m whole
length excl. modules. Bluetooth network reset: (1) Power off device
and disconnect from mains, apply short circuit between LED+ and
LED-, (2) connect device to mains and power on for at least 2
seconds, (3) power off device, disconnect from mains and remove
short circuit. Reset completed.
Emergency Lighting:
This LED power supply complies with EN 61347-2-13 Annex J and
is suitable for emergency lighting fixtures according to EN 60598-2-22.
1) Qualified Bluetooth mesh compact LED driver for independent
installation; 2) Constant current LED Power Supply; 3) t c point;
4) Made in Bulgaria by OSRAM; 5) picture only for reference, valid
print on product; 6) Radio frequency; 7) Wireless protocol; 8) Qualified
Bluetooth mesh; 9) Wireless range; 10) 10 m line of sight; 11) Mains;
12) Input; 13) Output; 14) Through looping; 15) Year; 16) Week;
17) Mounting hint for proper radio connectivity. 18) Do not place any
mains voltage or LED supply wires within or close to this area.
2
Cable type (tested acc. to EN 60598-1)
• NYM-J 3x1.5
• H05VV-F 3x1.5
25)
• NHXMH-J 3x1.5
• NYM-J 3x1.5
• H05VV-F 3x1.5
27)
• NHXMH-J 3x1.5
• Style 21073
• Style 21520
• H03VVH2-F 2x0.75
• H03VV-F 2x0.5
• H05VV-F 2x1.0
• H05VV-F 2x1.5
19) Recommended minimal distance to metal parts. 20) Placement
of integrated radio transmitter antenna; 21) Position; 22) Cable types
(tested acc. to EN 60598-1); 23) Remark; 24) A or B; 25) one cable;
26) A and B; 27) two cables; 28) Mains through wiring current ≤10A;
29) Safety information for mains through wiring: Cable temperature
in the cable clamp compartment depends on cable type, ambient
temperature and through wiring current. Therefore through wiring
current is limited. 2-wire connector for solid earthing conductors,
e.g. WAGO 2273-202, is recommended.
The device can be put into operation using the OSRAM HubSense
Commissioning Tool (https://platform.hubsense.eu), subject to
prior acceptance of the Terms of Use and the Privacy Policy. OSRAM
may terminate or suspend the use of the HubSense Commissioning
Tool at any time and for any or no reason in its sole discretion, even
if access and use is continued to be allowed to others.
Hereby OSRAM GmbH declares that the radio equipment types OTi
QBM 20 NFC I, OTi QBM 30 NFC I and OTi QBM 40 NFC I are in
compliance with Directive 2014/ 53/ EU. The full text of the EU dec-
laration of conformity is available at the following internet address:
www. osram. com/ot-indoor-ce.
NFC frequency range: 13 553 - 13 567 kHz
Bluetooth frequency range: 2402 - 2480 MHz
Max HF output power (EIRP) of the product: 4 dBm
Technical support: www.osram.com, +49 (0)89-6213-6000
22)
23)
Remark
Mains through wiring
current ≤10A*
28)
29)
Werbung
