Preparing To Install; Installation - BESAFE iZi Twist B i-Size Bedienungsanleitung

10
quality of the material may change.
• DO NOT use at home. It has not been designed for home use and can
only be used in a vehicle.
• When the child seat is mounted in the car check all the areas where
the child seat might touch the interior. We recommend using a
(BeSafe) protection cover in these places to avoid cuts, marks or
discolouration to the interior of the vehicle, especially in vehicles with
leather or wooden interiors.
• If in doubt, consult either the car seat manufacturer or the retailer.

Preparing to install

• Adjustable head rest
• Shoulder straps
• Baby insert
• Baby cushion
• Harness buckle
• Central adjuster
• Reclining handle
• Release handle head rest
• Installation screen
• Spirit level
• Battery compartment
• Floor support
• Floor support height indicator
• Height adjuster floor support
• Rotation release handle
• Switch for ISOfix connectors (2x)
• ISOfix connectors (2x)
• ISOfix release switch
• ISOfix indicators (2x)
• ISOfix car anchorage (2x)

Installation

1. When installing in the back seat of the vehicle, push the front seat of
the vehicle forward as far as possible and adjust the back rest into
an upright position (if it can be adjusted).
2. When installing in the front seat of the vehicle, adjust the back rest
into an upright position.
3. Position the vehicle on a horizontal surface when installing the seat.
4. When the base is lifted the floor support should fall downwards from
(1a)
(1b)
(1c)
(1d)
(1e)
(1f)
(1g)
(1h)
(1i)
(1j)
(1k)
(1l)
(1m)
(1n)
(1o)
(1p)
(1q)
(1r)
(1s)
(1t)
underneath the base. Do this outside the car.
5. Push down the Switch for the ISOfix connectors at both sides to
release the ISOfix connectors. (2)
6. Position the base on the vehicle seat. Click the ISOfix connectors on
to the ISOfix anchorages on the vehicle seat. Make sure that both
ISOfix indicators are green. (3)
7. Push the seat towards the backrest of the vehicle seat until it
touches the backrest. (4)
8. The ISOfix connectors will have resistance sliding in, in the most
outward positions, before they are connected with the ISOfix
anchorage of the vehicle.
9. Tip: once the ISOfix connectors are installed, the seat can be turned
towards the door of the vehicle to get a better view on the installation
display
10. Adjust the floor support, so it is in contact with the floor of the
vehicle. (5)
11. The height indicator of the floor support shows green when the floor
support is in contact with the floor. (5)
12. Lift the base at the front side (near the spirit level) and extend the
floor support till the spirit level is in the middle, showing a horizontal
position of the base. (5)
13. Tip: place one foot onto the bottom end of the floor support while
lifting the base to make adjusting the length at this step easier.
14. The alarm sound stops when the floor support indicators show green
and it is in contact with the floor and when the horizontal spirit level
shows a horizontal position of the seat. (5)
15. When having the child seat installed rearfacing in the back, it is
recommended to position the front vehicle seat in a way that it is
close to the touchpoint with the child seat. Make sure that the child
seat can still rotate freely.
When having the child seat installed rear facing on the passenger
seat in the front, it is recommended to position the passenger vehicle
in a way that the dashboard is close to the touchpoint with the child
seat. Make sure that the child seat can still rotate freely.
16. The seat is delivered with removable SIP+ (side impact protection +).
This extra side impact protection should be used on the doorside of
the vehicle. It can be connected by slotting between the seatshell and
the fabric. The seat already offers high level integrated side impact
protection. This extra side impact protection improves the protection
in the side impact still further. (Not on all models) (6)
17. Tip: For an optimal height of the SIP+, position it between the two
11