tau ARM200-Serie Bedienungs- Und Wartungsanleitung Seite 10

DESCRIPTION
The ARM200 automated system for swing gates is an electro-
mechanical non-reversing actuator that transmits motion to the leaf
via a worm screw system.
The actuator is available in more versions in 12 Vdc and 230 Vac.
The non-reversing system ensures the leaf is mechanically locked
when the motor is not operating. A convenient and safe release
system with customised key makes it possible to manually move
the leaf in the event of a malfunction or of a power failure.
ATTENTION:
The correct operation and the declared specifications
only apply if TAU accessories and safety devices
are used.
In the absence of a mechanical clutch, the use of
a control unit with an adjustable electronic clutch,
or the installation of a sensitive edge, is required in
order to ensure crush-proof safety.
The ARM200 automated system was designed and
built for controlling vehicle access. Avoid any other
use whatever.
ACTUATOR PARTS (fig.1)
Pos. Description
1 Actuator
2 Release device
3 Rod
4 Wing connection bracket
5 Rear bracket
6 Terminal board cover
DIMENSIONS (fig.2)
INSTALLATION (fig.3)
Electrical set-up (standard system - ARM200)
Pos. Description
1 Attuatore
2 Control unit
3 TX photocells
4 RX photocells
5 Key-operated selector switch
6 Flashing light and aerial
7 Mechanical stops
Electrical set-up (standard system - ARM200BENC)
Pos. Description
1 Attuatore
2 Control unit
3 TX photocells
4 RX photocells
5 Key-operated selector switch
6 Flashing light and aerial
7 Mechanical stops
Notes:
• Use suitable tubes and/or hoses to lay electric cables
• Choose short routes for cables and keep power cables separate
from control cables.
Preliminary checks
Prior to installing the automation, make all structural modifications
in order to ensure safety distances and protect and segregate
areas in which people may be exposed to the risk of crushing,
shearing, dragging or similar dangers.
10
•
•
•
•
•
•
•
Perform any necessary metalwork job before installing the
automated system.
The condition of the gate structure directly affects the
reliability and safety of the automated system.
Installation dimensions (fig.4)
Determine the fitting position of the actuator with reference to
fig.4.
Check with care if the distance between the open leaf and
any obstacles (walls, fences etc.) is higher than the actuator
dimensions.
Cables
4x1,5 mm²
3x1,5 mm²
(power supply)
4x0,5 mm²
2x0,5 mm²
3x0,5 mm²
2x1 mm² + 1RG58
-
Cables
2x2,5 mm² + 3x0,5 mm²
3x1,5 mm²
(power supply)
4x0,5 mm²
2x0,5 mm²
3x0,5 mm²
2x1 mm² + 1RG58
-
ARM200 Series
Make sure the existing structure is sufficiently sturdy and
stable;
the mechanical parts must conform to the provisions of
Standards EN 12604 and EN 12605;
leaf length in compliance with the actuator specifications;
regular and uniform movement of the leaves, without any
friction and dragging during their entire travel;
stiff hinges in good conditions;
presence of both opening and closing mechanical limit stops;
presence of an efficient earthing for electrical connection of the
actuator.
X° A (mm)
90 80 ÷ 85
90 90
90 95
90 100
90 105
A
90 110 ÷ 115
90 120
R
90 125
90 130
M
90 135
90 140
90 145 ÷ 150
2
90 155
90 160
2
90 165
90 170
90 175 ÷ 180
5
100 100 ÷ 120
100 125
100 130
100 135
100 140
100 145
100 150
X° A (mm)
A 90 80 ÷ 175
90 180 ÷ 185
90 190
R
90 195
90 200
M
100 100 ÷ 150
100 155
100 160
2
100 165
100 170
5
100 175
100 180
100 185
0
100 190
100 195
100 200
B (mm) C (mm)
110 ÷ 200 20 mm
110 ÷ 195 20 mm
110 ÷ 190 20 mm
110 ÷ 185 20 mm
110 ÷ 180 20 mm
110 ÷ 175 20 mm
110 ÷ 170 20 mm
110 ÷ 165 20 mm
110 ÷ 160 20 mm
110 ÷ 155 20 mm
110 ÷ 150 20 mm
110 ÷ 145 20 mm
110 ÷ 140 20 mm
110 ÷ 135 20 mm
110 ÷ 130 20 mm
110 ÷ 125 20 mm
110 ÷ 120 20 mm
110 ÷ 150 20 mm
110 ÷ 145 20 mm
110 ÷ 140 20 mm
110 ÷ 135 20 mm
110 ÷ 130 20 mm
110 ÷ 125 20 mm
110 ÷ 120 20 mm
B (mm) C (mm)
115 ÷ 250 20 mm
115 ÷ 245 20 mm
115 ÷ 240 20 mm
115 ÷ 235 20 mm
115 ÷ 230 20 mm
115 ÷ 250 20 mm
115 ÷ 245 20 mm
115 ÷ 240 20 mm
115 ÷ 235 20 mm
115 ÷ 230 20 mm
115 ÷ 225 20 mm
115 ÷ 220 20 mm
115 ÷ 215 20 mm
115 ÷ 210 20 mm
115 ÷ 205 20 mm
115 ÷ 200 20 mm