Inhaltsverzeichnis
Werbung
Modifications: Any modifications made to this device that are not approved by
RTX Telecom A/S may void the authority granted to the user by the FCC to
operate this equipment.
RF Exposure:This device complies with FCC RF exposure limits as set forth in
CFR47 section 2.1091 and section 2.1093 addressing RF exposure from Radio
frequency devices.
This device complies with the RF exposure requirements in Industry Canada
RSS-102 issue 2.
WARNING:To ensure compliance with FCC and Industry Canada RF
exposure requirements, the IP DECT Stand must be installed to provide a
separation distance of at least 20 cm from all persons nearby. This device
must not be co-located or operating in conjunction with any other antenna or
transmitter.
For body worn operation, the 5610 Cordless Handset has also been tested and
meets the FCC RF exposure guideline when used with the Mitel belt clip
supplied for this product. Use of other accessories may not ensure compliance
with FCC and Industry Canada RF exposure guidelines.
Notice to Customers in EU Countries
We, RTX Telecom A/S.
Of, RTX Telecom A/S
Stroemmen 6
9400 Noerresundby
Denmark
Declare that for the hereinafter mentioned product the presumption of
conformity with the applicable essential requirements of
DIRECTIVE 1999/5/EC OF THE EUROPEAN
PARLIAMENT (RTTE DIRECTIVE) AND OF THE COUNCIL
Mitel IP DECT Stand and 5610 Cordless Handset
Any unauthorized modification of the product voids this Declaration.
For a copy of the original signed Declaration of Conformity (in full conformance
with EN45014), please contact the Regulatory Approvals Manager at the above
address.
Notice to Customers in Australia
• Do not use the cordless handset in areas where there are explosive
hazards.
• Do not use the cordless handset in environments where there is a danger
of ignition of flammable gases.
Description
®
The Mitel
5610 Cordless Handset and IP DECT Stand provide SIP call
processing features on a cordless handset. The IP DECT stand supports up to
eight cordless handsets.
The IP DECT stand connects to the network through the PC port on a Mitel
5312, 5320, 5324, 5330, 5340, or 5360 IP Phone. The IP DECT stand extends
the SIP phone functionality from the communications platform to the handsets.
You can purchase additional handsets and chargers from the Mitel Customer
Service order desk.
The cordless handset has an indoor signal range of up to 50 meters (150 feet)
from the IP DECT stand and an outdoor range of up to 300 meters (900 feet).
Note that this range can be limited by concrete or metal barriers. To extend the
signal range, you can purchase an optional IP DECT Stand Repeater.
A
Figure
provides an overview of the completed installation.
What You Received
• 5610 Cordless Handset
• Handset Charging Cradle
• Power supply adapter for Charging Cradle
• IP DECT Stand
• Short CAT5 LAN cable
• Power supply adapter for IP DECT Stand
4
is given.
• Belt clip
• Belt clip removal tool
What You Require
• 3300 Internet Communications Platform (ICP) with MCD Release 4.0 SP1
or later software,
or
Mitel 5000 Communications Platform (CP) with v4.0 or later software
• Mitel 5312, 5320, 5324, 5330, 5340, or 5360 IP Phone
• Two power extension cords with C7 plugs (purchase from Mitel Networks)
IP DECT Stand Rear Panel Components (See Figure
#
Description
LAN Port: Connects to PC port on Mitel IP Phone via short Ethernet cable.
LAN LED:
OFF: IP DECT stand is not connected to LAN.
ON: IP DECT stand is connected to the LAN.
VOIP LED:
OFF: IP DECT stand is not connected to communications platform.
ON: IP DECT stand is connected to communications platform.
CALL LED
OFF: No call in progress.
ON: Call in progress.
POWER LED
OFF: Power is not connected.
ON: IP DECT stand is powered on.
POWER Input: Connects to the AC power adapter for IP DECT stand. Note that
there are two different power adapters. One is for the IP DECT stand; the other
for the handset charger. The connectors at the end of each adapter cord are dif-
ferent.
RESET button: Press to activate configuration changes or to enable handset
registration. The first handset automatically registers with the IP DECT Stand
after approximately 30 seconds. To register each additional handset on the
same IP DECT Stand, you must first reboot the stand by pressing the RESET
button on the rear panel of the stand.
You can also reset the stand configuration (including the admin user name and
password) to the default values using the this button. Press and hold the Reset
button for greater than 10 seconds to reset the stand.
Note that you cannot reset the stand while a call is being supported on a hand-
set that is registered to the stand.
B
)
Werbung
Inhaltsverzeichnis
