Inhaltsverzeichnis
Werbung
C
Important Safety Instructions and Precautions
WARNING:DO NOT CONNECT DIRECTLY TO THE PUBLIC SWITCHED
TELEPHONE NETWORK (PSTN). ANY CONNECTION OF THIS PHONE
TO AN OFF PREMISE APPLICATION, AN OUT OF PLANT APPLICATION,
ANY OTHER EXPOSED PLANT APPLICATION, OR TO ANY EQUIPMENT
OTHER THAN THE INTENDED APPLICATION MAY RESULT IN A SAFETY
HAZARD, AND/OR DEFECTIVE OPERATION, AND/OR EQUIPMENT
DAMAGE. "EXPOSED PLANT" MEANS WHERE ANY PORTION OF THE
CIRCUIT IS SUBJECT TO ACCIDENTAL CONTACT WITH ELECTRIC
LIGHTING OR POWER CONDUCTORS OPERATING AT A VOLTAGE
EXCEEDING 300 V BETWEEN CONDUCTORS OR IS SUBJECT TO
LIGHTNING STRIKES.
WARNING:THE SOCKET OUTLET, IF USED, SHALL BE LOCATED NEAR
THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE BY THE USER.
WARNING:USE RTX TELECOM A/S APPROVED POWER ADAPTER
(MITEL PART NUMBER 51015401) WITH THE IP DECT STAND. USE RTX
TELECOM A/S APPROVED POWER ADAPTER (MITEL PART NUMBER
51015403) WITH THE 5610 HANDSET CHARGING CRADLE. USE ONLY
WITH UL AND CSA (CUL) LISTED DETACHABLE POWER CORDSET
WITH NON-POLARIZED PLUG IN ONE OF THE FOLLOWING CORD TYPE
(SV, SVE, SVO, SVOO, SVT, SVTO, SVTOO, SP-2, SPE-2, SPT-2, NISP-2,
NISPE-2, NISPT-2, SP-3, SPE-3, SPT-3) WITH CORD SIZE AWG 20.
WARNING:THE MITEL IP DECT STAND AND 5610 HANDSET ARE FOR
USE ONLY WITH SPECIFIED MITEL EQUIPMENT.
When using the telephone equipment, basic safety precautions should always
be followed to reduce the risk of fire, electrical shock, and injury to persons,
including the following:
• Read and understand all instructions.
• Follow all warnings and instructions marked on the product.
• This equipment is not connected to the Telecommunication Network and
the working voltage does not exceed 60Vdc. It is not located in separate
buildings.
2
IP DECT Stand connects to 5312, 5320, 5324, 5330, 5340, and 5360 IP Phones
• Do not use this product near water; for example, near a sink or in a wet
area.
• Do not place this product on an unstable cart, stand, or table. The
telephone can fall, causing serious damage to the unit.
• To protect the product from overheating, do not block or cover any slots or
openings in the base unit. This product should never be placed near or
over a radiator or heat register. This product should not be placed in a
built-in installation unless the proper ventilation is provided.
• This product should be operated only from the type of power source
indicated on the marking label.
• Do not allow anything to rest on the power cord.
• Do not locate this product where the cord will be damaged by people
walking on it.
• Do not overload wall outlets and extension cords, as this can result in the
risk of fire or electrical shock.
• Never push objects of any kind into this product through the base unit slots,
as they may touch dangerous voltage points or short out parts that could
result in a risk of fire or electrical shock. Never spill liquid of any kind on the
product.
• To reduce the risk of electric shock, do not disassemble this product.
Contact qualified service personnel when some service or repair work is
required. Opening or removing covers may expose you to dangerous
voltages or other risks. Incorrect reassembly can cause electric shock
when the appliance is subsequently used.
CAUTION:
There is danger of explosion if batteries are mishandled or incorrectly
replaced. On systems with replaceable batteries, replace only with the same
manufacturer and type or equivalent type recommended by the manufacturer per the
instructions provided in the product service manual. Do not disassemble batteries or
attempt to recharge them outside the system. Do not dispose of batteries in fire. Dispose
of batteries properly in accordance with the manufacturer's instructions and local
regulations. Use only with brand BAK, model BAK06-AS02-101281; 3.7VDC 650mAh Li-
ion rechargeable battery.
Werbung
Inhaltsverzeichnis
