Advanced Programming - Beninca CP.BULL5 ARC Bedienungsanleitung

8) ADJUSTMENT OF THE TORQUE (DIP1:ON)
When DIP1 is moved to ON, the board indicates that the torque has been applied during a number of flashes (from 1 to 4) of the DL2
green LED, followed by a 3-s interval. The max torque is indicated with DL2 green LED with fixed light. To increase the torque, press
P1. The DL2 LED changes the number of flashes to indicate the selected torque value. Once the desired torque is selected, move DIP
1 to OFF to memorise this presetting.

9) ADVANCED PROGRAMMING

If necessary, it is possible to modify the functions of the PP and STOP inputs to obtain OPEN/CLOSE inputs or alternatively OPEN/
Pedestrian inputs; proceed as follows:
1) Move all DIPs to OFF
2) Move DIP1 to ON
3) to change the Step/Step input to Open, move DIP 2 to ON
4) to change the STOP input to Close, move DIP 3 to ON and DIP 4 to OFF
5) to change the STOP input to Pedestrian, move DIP 4 to ON and DIP 3 to OFF
6) move DIP 6 to ON. The LEDs will flash alternatively for approx. 10 secs.
7) after 10 seconds, the LEDs will flash simultaneously and the new input functions will be stored.
8) move the dips to OFF
9) move the DIPs back to the desired settings
10) PRE-WARNING ACTIVATION/DEACTIVATION (DIP1:ON)
As soon as DIP1 is to ON, the DL1 red LED indicates whether the pre-warning flashing is activated.
The pre-warning function can be activated or deactivated with P2 key.
LED DL1 On: Activated pre-warning, the indicator lamp switches on for approx. 3 seconds before the motor starts.
LED DL1 Off. Pre-warning is deactivated.
11) RADIO SELF-LEARNING (DIP1:OFF)
The radio receiver in this product is EXCLUSIVELY compatible with the new ARC (Advanced Rolling Code) transmitters which, thanks to
128-bit encryption ensure superior copy-security.
To use a remote control, it is first necessary to store its code in memory. The memorisation procedure is described hereunder. The device
is able to store up to 64 different codes in memory.
By pressing P1, the control unit enters the radio learning phase: DL1 red LED flashes 1 time per second, awaiting the key to the matched
to the Step-by-Step function;
When the key is stored in memory, exit from the programming mode;
By pressing P1 twice, the DL1 red LED flashes 2 times per second and the pedestrian learning phase is entered (the pedestrian function
controls an opening operation of 7s). When the key to be matched is memorised, exit from the programming mode.
If the programming mode must be left without storing any remote control signal, press P1 key until DL1 red LED starts to flash in "power
on" mode (see LED diagnostics).
11.1) RECEIVER RESET
To reset the memory of the receiver, press and keep P1 and P2 keys pressed for around 10 seconds (during this period of time, both DL1
and DL2 flash rapidly). After 10 seconds, when the two LEDs are switched on with fixed light, release the push-buttons. When the LEDs
switch back again to the original configuration, the control unit has completed the memory reset.
NOTE: The transmitters are memorised on an EPROM memory (U3), which can be extracted from the control unit and inserted in a new
CP.BULL5 ARC control unit should a replacement is required.
For safety reasons, the transmitters can be stored in memory during the opening/closing of the motor.
12) TRANSMITTER REMOTE LEARNING
If the transmitter code is already stored in the receiver, the remote radio learning can be carried out (without accessing the control unit).
IMPORTANT: The procedure should be carried out with gate in the opening phase, during the TCA dwell time.
Proceed as follows:
1) Press the hidden key of the transmitter, the code of which has already been stored in memory.
2) Within 5 seconds, press the already memorised transmitter key corresponding to the channel to be
matched to the new transmitter. The flashing light switches on.
3) Within 10 seconds, press the hidden key of the new transmitter.
4) Within 5 seconds, press the key of the new transmitter to be matched to the channel selected at item 2.
The flashing light switches off.
5) The receiver stores the new transmitter code and exits from the programming mode immediately.
11