Important Safety Instructions - Bestway 65054 Benutzerhandbuch

#65054; #65055
Owner's manual
Warning

IMPORTANT SAFETY INSTRUCTIONS

Read the manual and follow the instructions relating to safety tips,
correct and complete product assembly, setting into service, use
and maintenance.
For your own safety, always heed the advice and warnings in these
instructions. Non-compliance with these operating instructions may
expose you to serious danger or death. Only use the product in the
places and conditions for which it is intended.
Stand-up Paddling is a dangerous sport. Use of this product
exposes the user to unexpected risks, dangers and hazards.
User should realize and understand these risks. The use of this
product implies the respect of the safety instructions described in
the manual.
Do not exceed the maximum recommended number of persons.
Regardless of the number of persons on board, the total weight of
persons and equipment must never exceed the maximum recommended load.
Do not use this product if you are under the influence of alcohol, drugs or medications.
Life saving devices such as life jackets and buoys should be pre-inspected and used at all times. Always wear a helmet
when using this product.
Always paddle with an experienced partner when using this product.
Tell your sail routes and time schedule to your partner.
Check the weather forecast first to know the marine environment and weather conditions before starting. Bad weather
and marine environment is very dangerous.
Never use this product in conditions that are beyond your ability (such as, but not limited to, high surf, riptides, currents
or river rapids)
Use the product near the shore and beware of natural factors such as wind, tidewaters and tidal waves. BE AWARE OF
OFFSHORE WINDS AND CURRENTS.
Before every use, carefully inspect the product for signs of wear or leakage to ensure everything is in good condition.
Please do not use the SUP if you find any damage.
Do not surf in unfamiliar water areas.
Beware of potential harmful effects of liquids such as battery acid, oil and petrol. These liquids may damage the
product.
Inflate according the rated pressure on the product or it will cause over inflation and/or an explosion.
Stay balanced. Uneven distribution of loads on the board may cause the board to overturn which could lead to
drowning.
Know how to operate this product. Check your local area for information and/or training as needed. Inform yourself
about local regulations and dangers related to surfing, boating and/or other water activities.
SAVE THESE INSTRUCTIONS
Technical Specifications
Item Inflated Size
65054； 3.10 m x 68 cm x 10 cm
(10'2" x 27" x 4")
65055
#65054
Surf Board Components:
(65054ASS17) • 1 Wrench(F6H189)
• Pressure gauge(P5C412)
• Polyester 3-ply patch
Footrest Tube
(P5C499)
Footrest Foam Safety Rope (P6C786)
(F6C211)
#65055
Surf Board Components:
(65055ASS17) • 1 Wrench(F6H189)
• Pressure gauge(P5C412)
• Polyester 3-ply patch
Removable Fin Safety Rope (P6C786)
(F6C210)
DRAWING
7
8
9
10
2
6
3
1
4
5
S-S-005417/21x28.5cm(65054;65055)
TO THE STORE
QUESTIONS? PROBLEMS?
MISSING PARTS?
For FAQ, Manuals Or
Spare Parts, Please Visit
www.bestwaycorp.com
Recommended Maximum Load Maximum Number
Working Pressure Capacity of Persons
0.827 bar 100 kg
(12 psi) (220 Lb.)
Elastic Cord
(F2C098)
High Pressure
Hand Pump
Removable Fin Oar (F6C216)
(P3046B)
(F6C210)
Seat (F6C212Q16) Air Valve Travel Bag
(P6H971) (F6H433Q17)
High Pressure Oar (F6C236)
Hand Pump
(P3046B)
Elastic Cord Air Valve Travel Bag
(F2C098) (P6H971) (F6H433Q17)
REF. NO. DESCRPITION
1 Air Valve
2 Soft Handle
3 Side Fin
4 Removable Fin
5 Big D-ring
6 Seat (For 65054 only)
7 Small D-ring
8 Footrest holder (For 65054 Only)
9 Footrest (For 65054 Only)
10 Ring (For 65054 Only)
JS-YF-2016-B-11229/英
Installation
1. Spread out the surf board on level ground.
2. Assemble the removable fin to the bottom of the board (Fig.1). Make sure the curvature of the fin is pointed towards
the back end of the board (Table 1 pos.4)
NOTE: Assemble the fin before inflation and also disassemble it after deflation.
NOTE: To avoid damage to the removable fin, do not enter shallow water.
Fig. 1
3. Inflate the board by unscrewing the cap of the air valve (Fig.2 pos.1). Ensure that the inner spring valve is not
depressed. If it is depressed (Fig. 2 pos. 2), press the spring valve and turn counter clockwise so the inner spring
valve is in the correct position (Fig.2 pos. 3). Attached the pressure gauge onto the hose and the hose to the inflate
position on the high-pressure hand pump. Inflate the board to 0.827 bar (12 psi). After inflation, screw the cap of air
valve (Fig.2 pos. 4)
NOTE: If over-inflation occurs, press the spring valve to release air to an acceptable level and securely fasten the air
valve.
NOTE: If the board is not in use and exposed under the sun, it may cause overexpansion and damage the board. Check
the pressure and deflate slightly until the correct pressure is obtained.
NOTE: Pressure gauge is for inflation purpose only, and the value of the pressure gauge is just for reference, should not
be used as a precision instrument.
1 adult
1
Fig. 2
4. Use your board at first time or after long period storage, check the air valve and tighten the valve with the provided
wrench first. (Fig. 3).
Attention: Don't adjust the air valve when the board is in use.
Warning: Don't rotate the wrench counterclockwise when inspect the inflation, or it will be danger.
Fig. 3
5. Assemble the seat (Included with product #65054 only). Connect the seat to the ring on the board. The seat can be
adjusted to accommodate the footrest.
6. Attach the safety rope to the tow ring (Table 1 pos.5), and place the belt around your ankle (Fig.4)
Fig. 4
Deflation
QTY
1
1
2
1
1
1
4
Storage
1. Deflate the board by unscrewing the cap of air valve, press the spring valve and turn clockwise.
1
2. Remove all the accessories from the board. Use a cloth to gently dry all surfaces. Keep the board and all accessories
1
clean and dry.
2
3. Fold the board from front to back to remove additional air. You can also drain any remaining air using the high
pressure hand pump by connecting the hose to the deflatation port on the high-presure hand pump.
4. Store in a cool, dry place and out of children's reach.
Repair
• Fully clean the area to be repaired.
• Cut the correct size from the repair patch material.
• Apply only the amount of glue (not included) needed to cover the repair site.
• Press the repair patch firmly to repair site for 30 seconds.
Table 1
• Wait for 1 hour before inflation.
3
2 3 4
S-S-005417