Controls And Functions - JB Systems MCD200 Bedienungsanleitung

ENGLISH
CLEANING THE CD-PLAYER:
Clean by wiping with a polished cloth slightly dipped with water. Avoid getting water
inside the unit. Do not use volatile liquids such as benzene or thinner which will
damage the unit.
CONNECTIONS
• Use the supplied cinch cable to connect the audio output of the CD player with a
CD input on your mixing unit.
• Also connect the fader start cable if your audio mixer has fader start connections.
(Synq® or Pioneer® compatible)
• Connect the mains cable.

CONTROLS AND FUNCTIONS

1. SEARCH Button: This button has 4 forward and 4 backward speed positions for
searching through songs. The more you turn the wheel in either direction the
faster you will search through the music.
2. TRACK SEARCH Buttons: These buttons are used to select the track to be
played. Forward skip & back skip.
JB SYSTEMS®
USER MANUAL
3/53 MCD200
ENGLISH
3. IN/R.CUE button: Allows you to set the cue point without stopping the playback
(CUE ON THE FLY). This button also sets the beginning of a seamless loop.
When you play one of the hot cues(19), the starting point is also copied to this
button.
4. OUT/EXIT button: Used to set the endpoint when looping music. The player
starts to loop seamlessly until you press this button again to exit. When a loop is
programmed but not active you can also restart the loop. The point where you
press the button will be memorized as the new end point of the loop. When the
player is in "loop edit mode" pressing this button stops the loop editing and saves
the current endpoint of the loop.
5. RELOOP/STUTTER button: This button has 3 functions:
• RELOOP: If a loop is programmed and you have hit the OUT/EXIT button(4),
press the reloop button to enter the loop again. Just press the OUT/EXIT(4)
button to exit the loop. (intro and end points of the loop are unchanged)
• STUTTER: When a loop is playing you can press this button to restart the
loop at once. You can also press this button when a track is not playing in
loop. Every time the RELOOP/STUTTER button is pressed, it will restart the
music from the preprogrammed cue point. This stutter effect adds extra
creativity to your performance.
• LOOP EDIT: When a loop is programmed, press the RELOOP/STUTTER
button for about 2 seconds to enter "loop edit" mode. Now you are able to
change the endpoint of the loop. See chapter "How to use..." for more
information.
6. CUE button: Pressing the CUE button during playback provides an immediate
return to the position at which playback was started. Playback starts immediately
from the programmed cue point for as long as the CUE button is pressed. The
CD player jumps back to the cue point as soon as the CUE button is released.
Also with the unit in pause mode (Play/Pause LED blinks) the search and/or jog
wheel is used to set a different start point. By pressing "PLAY/PAUSE" button
then "CUE", you can confirm this new cue point.
7. SCRATCH button: Used to put the MCD200 in scratch mode. This option gives
you the possibility to scratch any track on the CD in real time. You can use the
scratch function in both play and pause mode:
• In play mode: The music plays normally until you turn the big jog wheel(20).
While manipulating the jog wheel(20), the scratch effect is audible. Once the
jog wheel is stopped, the music continues playing from the point where you
stopped turning it.
• In pause mode: the music is paused for as long as the jog wheel(20) isn't
moved. When you start manipulating the jog wheel(20), the scratch effect is
audible. Once the jog wheel is stopped, the music stops playing and waits in
pause mode.
NOTE: during scratch mode you can switch between play and pause mode by simply pressing the
PLAY/PAUSE button(8)
8. PLAY/PAUSE button: every time you press the PLAY/PAUSE button the CD
player changes from play to pause or from pause to play. The button blinks as
long as the player is set to pause.
9. MEMORY Button: is used to store cue points and loops to the Hot Cue
buttons(19) and to the permanent cue memory:
• Storing to HOT CUE buttons: Press the MEMORY button shortly to
prepare the MCD200 for storing a cue point or loop to one of the 4 HOT
CUE buttons.
JB SYSTEMS®
USER MANUAL
4/53 MCD200