Usb Operation; Bluetooth Operation; Aux-In Operation - Sharp PS-920 Bedienungsanleitung

NOTE: in order to get the best reception, extend the FM ANT.
on the rear of the unit before use to its full length.
TUNING TO A RADIO STATION
If you know the station frequency that you want to tune to directly:
• Tune to a station by press the
ly. Hold them to search upward or downward. The station frequency is
shown on the display.
To tune to a preset station:
• To tune to the next preset station, press the 10/M./FOLD.+ button.
• To tune to the previous preset, press the 10/M./FOLD.- button.
AUTO PRESET MEMORY/SCAN
To scan for stations within reception range and save them to preset
memory automatically, press and hold the
unit is nished scanning, the unit will automatically tune to preset number
1 (P01).
MANUAL PRESET MEMORY OPERATION
Choose which stations to save in preset memory instead of scanning
automatically.
1. Use the / TUN.+ or / TUN.- button to tune to the station that you
want to save as a preset (e.g., 93.1).
2. Press the P-MODE/M. button. "P01" will ash on the display to indicate
that you are saving the station as Preset Memory 01. (To change the
preset memory number, press the 10/M./FOLD.+ or 10/M./FOLD.-
buttons.)
3. Press the P-MODE/M. button to nish saving the station (e.g., P01 is
now set to 93.1).
4. To save another station, repeat steps 1 to 3. You may save up to 30 FM
stations.

USB OPERATION

This unit provides two USB ports for music playback.
1. Press the FUNCTION button on unit to select "USB1" or "USB2" mode.
2. Plug the USB memory stick to the USB port on top of the unit. Playback
will start automatically from Track 1.
3. To pause playback, press the
time will ash on the display.
4. To resume playback, press the
5. To select a desired track, press the
respectively during playing until the desired track appears on the
display. The unit will start play automatically.
6. To search for a particular passage during playback, press and hold the
/TUN.+ or /TUN.- button to scan the current playing track at high
speed until desired point (passage) appears, then release the button for
normal playback mode.
7. To select a song which track number exceeds 10, press the 10/M./
FOLD.+ or 10/M./FOLD.- button each time to skip forward/backward
10 tracks, then press the
desired track.
8. To select a desired folder (if the USB contains more than one folder),
press and hold the 10/M./FOLD.+ or 10/M./FOLD.- button each time to
skip forward/backward a folder, then press the
button to select desired track.
IMPORTANT: The USB port is intended for data transfer only,
other devices cannot be used with this USB connection. The use
of USB extension cords is not recommended. Don't unplug the
USB from the unit when playing or reading the USB device.
REPEAT PLAY
You can play one track or all tracks on the USB repeatedly.
To Repeat a Single Track
1. Press P-MODE/M. button on unit during play, the display will show "
" and the current track will be played over an over again.
/ TUN.+ or / TUN.- button repeated-
/BT/SCAN button. After the
/BT/SCAN button on unit. The playing
/BT/SCAN button again.
/TUN.+ or /TUN.- button
/TUN.+ or /TUN.- button to select
/TUN.+ or
2. To cancel repeat play, press P-MODE/M. button on unit until "
disappears from the display.
To repeat all the Tracks
1. Press P-MODE/M. button on unit until the "
display, all tracks on the USB will be played over and over again.
2. To cancel repeat play, press the P-MODE/M. button on unit until "
disappears from the display.
To repeat the folder (only for USB which contains more than one
folder)
1. Press the P-MODE/M. button on unit until "
on the display, the current folder will be repeated over and over again.
2. To cancel repeat play, press the P-MODE/M. button on unit until "
FOLDER" disappears from the display.
RANDOM PLAY
Press the P-MODE/M. button on unit in play mode till the "RAND"
shows steadily on the display, the random play will start from next track
automatically. Press the P-MODE/M. button on unit again until the
"RAND" disappears from the display to cancel.

BLUETOOTH OPERATION

1. Press the FUNCTION button on unit to switch to BLUETOOTH function,
the LCD will display "bt" and the pair indicator will ash at high speed.
2. Turn on the Bluetooth function on the device, scan the unit "PS-920"
and connect, then input the password 0000 if required, the pair
indicator keep light up to indicate connection done, and the display
will show "bt". Press Play to start playback.
3. Rotate the VOLUME knob on the unit or adjust the volume on the
external device to increase or decrease the music volume to your
desired level.
4. Press and hold the
NOTE: The Bluetooth works best within 10 meters in open air.

AUX-IN OPERATION

1. Press the FUNCTION button on unit to select the "AUX" mode.
2. Connect your audio device to the AUX IN jack on the top panel of the
unit with an AUX IN cable.(audio cable is not included)
3. Rotate the VOLUME knob on the unit or adjust the volume on the
external device to increase or decrease the music volume to your
desired level.
4. Control the playback with your audio device.
MIC JACK OPERATION
Microphone input is available in all modes.
1. Connect your microphone to the 6.3mm MIC JACK found on the top
panel of the unit.
2. Rotate the MIC VOL. knob on the unit to increase or decrease the
microphone volume.
3. Press the ECHO Button to turn on or o the echo e ect of the
microphone.
/TUN.-
" shows steadily on the
FOLDER" shows steadily
/BT/SCAN button to disconnect Bluetooth.
5
"
"