Makita UR101C Betriebsanleitung Seite 22

Speed Mode
indicator
High
Medium
Low
Automatic Torque Drive Technology
When you turn on the Automatic Torque Drive
Technology (ADT), the tool runs at optimum rotation
speed and torque for the condition of grass being cut.
The tool automatically detects the cutting tool attached
and chooses a suitable rotation speed.
To start ADT, press and hold the reverse button until the
ADT indicator turns on.
To stop ADT, press and hold the reverse button until the
ADT indicator turns off.
► Fig.9: 1. ADT indicator 2. Reverse button
Indicator Mode
ADT
Reverse button for debris removal
WARNING:
Switch off the tool and disconnect
the portable power pack from the tool before you
remove entangled weeds or debris which the
reverse rotation function can not remove. Failure
to do so may result in serious personal injury from
accidental start-up.
This tool has a reverse button to change the direction of
rotation. It is only for removing weeds and debris entan-
gled in the tool.
To reverse the rotation, tap the reverse button and pull
the switch trigger while depressing the lock-off lever
when the cutting tool is stopped. The speed indicators
and ADT indicator start blinking, and the cutting tool
rotates in reverse direction when you pull the switch
trigger.
To return to regular rotation, release the trigger and wait
until the cutting tool stops.
► Fig.10: 1. Speed indicator 2. ADT indicator
3. Reverse button
Rotation speed
Cutter blade Nylon cutting
Plastic blade head
(305 mm) Plastic blade
(255 mm)
0 - 7,000 0 - 5,500
-1 -1
min min
0 - 5,500 0 - 5,000
-1 -1
min min
0 - 4,600 0 - 4,600
-1 -1
min min
Cutting tool Rotation
speed
Cutter blade 3,500 - 7,000
-1
Plastic blade min
(305 mm)
Nylon cutting 3,500 - 5,500
-1
head min
Plastic blade
(255 mm)
NOTE: During the reverse rotation, the tool operates
only for a short period of time and then automatically
stops.
NOTE: Once the tool is stopped, the rotation returns
to regular direction when you start the tool again.
NOTE: If you tap the reverse button while the cutting
tool is still rotating, the tool comes to stop and to be
ready for reverse rotation.
Electric brake
This tool is equipped with an electric brake. If the tool
consistently fails to quickly stop after the switch trigger
is released, have the tool serviced at our service center.
CAUTION:
This brake system is not a substi-
tute for the protector. Never use the tool without
the protector. An unguarded cutting tool may result
in serious personal injury.
Electronic function
Constant speed control
The speed control function provides the constant rota-
tion speed regardless of load conditions.
Soft start feature
Soft start because of suppressed starting shock.
ASSEMBLY
WARNING:
switched off and the portable power pack is dis-
connected from the tool before carrying out any
work on the tool. Failure to switch off and disconnect
the portable power pack may result in serious per-
sonal injury from accidental start-up.
WARNING:
completely assembled. Operation of the tool in a
partially assembled state may result in serious per-
sonal injury from accidental start-up.
Installing the handle
For UR101C
1. Insert the shaft of the handle into the grip. Align
the screw hole in the grip with the one in the shaft.
Tighten the screw securely.
► Fig.11: 1. Grip 2. Screw 3. Shaft
NOTICE:
Note the direction of the grip. The
screw holes will not be aligned if the grip is not
inserted in the correct direction.
2. Place the spring onto the base.
► Fig.12: 1. Knob 2. Handle clamp 3. Handle
4. Handle holder 5. Spring 6. Base
3. Place the handle between the handle clamp and
handle holder.
22 ENGLISH
Always be sure that the tool is
Never start the tool unless it is