Functional Description - Makita VC3211H Bedienungsanleitung

FUNCTIONAL DESCRIPTION

WARNING:
Before plugging the cleaner, always make sure
•
that the cleaner is switched off. Plugging the
cleaner with the switch on may cause an
unexpected start resulting in serious personal injury.
Switch action
Fig.1
To start the cleaner, rotate the switch lever to the "I" side.
To stop it, rotate the switch lever to the "O" side.
Fig.2
The suction force can be adjusted according to your
work need.
Suction force can be increased by turning the suction force
adjusting knob from the
Also, set the hose diameter selection dial to the hose's
diameter that you are going to use.
Hose diameter selection dial
Turn the dial direction in accordance with the hose you
use.
NOTE:
Do not set the dial at the middle. Always turn either side
according to the hose diameter.
Warning beep
There are two types of beeping sound. One is short
beeps, and the other is long beep.
When the air flow speed falls under 20 m/s, the cleaner
emits short warning beeps for safety reasons. When it
sounds, check the hose diameter selection dial or if the
suction force is not too low. If the beeps keep sounding,
perform maintenance or ask your local service center.
When the tank is filled with liquid, the cleaner emits long
warning beep.
When the tank is full and the beep sounds, switch off
the cleaner and empty the tank.
Connecting electric power tools
WARNING:
Make sure that both the cleaner and the electric power
•
tool are switched off before connecting or disconnecting.
Connecting the power tool to the cleaner with both of
them being switched on may cause unexpected and
sudden start resulting serious personal injury.
Never connect an electric power tool with an input
•
power exceeding
"SPECIFICATIONS" to the socket of the cleaner
by turning the suction force adjusting knob.
Connecting the electric power tool exceeding the
specified input power may cause overheat and
damage to the cleaner.
symbol to the symbol.
that specified in
When connecting a grounded tool, insert a plug
•
with a grounding plate to the socket of the cleaner.
The cleaner can be connected to an electric power tool
up to input power shown in the "SPECIFICATIONS".
Fig.3
Fig.4
1. To connect an electric power tool, open the outlet
cap and insert the power tool plug into the socket
of the cleaner.
Fig.5
2. When connecting an electric power tool, secure
the power supply cord and hose by the hose
bands at regular distance. It prevents the hose
from entangling the power supply cord.
3. Rotate the switch lever to the "AUTO" position.
4. Move the suction force adjusting knob to the
position suitable for the input power of the electric
power tool you intend to use.
5.
Switching on and off of the connected electric power
tool simultaneously brings the cleaner switching on and
off action. The cleaner still works for a few seconds
even after the electric power tool is switched off.
6. After use, disconnect the power tool from the
socket of cleaner.
7. Switch off the cleaner after use.
Auto-suction stop during suction operation
WARNING:
Do not pick up foam or soapy liquid. Picking up
•
foam or soapy liquid can cause foam to come out
of air exit before the auto-suction stop works.
Continuing to using in this condition may cause an
electric shock and breakage of the cleaner.
The cleaner has a mechanism that prevents water from
immersing into the motor when picking up more than a
certain amount of water.
When the tank is full with liquid, the cleaner emits long
warning beep. Switch off the cleaner and empty the tank
when this beep sounds.
Usage of base hook
CAUTION:
Be careful not to pinch your fingers when
•
closing the base hook. Failure to do so may
cause personal injury.
NOTICE:
Do not apply an excessive force on the base hook.
•
The excessive force on the base hook may damage
the base hook. Close the base hook when not in use.
Opening the base hook allows the following usage.
the
1. Storing the power supply cord
Fig.6
NOTICE:
Do not use the cleaner or a connected electric
•
power tool with a power supply cord wound on
8