Makita SD100D Betriebsanleitung Seite 8

Type of saw blade
For drywall
For wood
LED light
CAUTION:
Do not look in the light or see the
source of light directly.
Pull the switch trigger to light up the lamp. The lamp
keeps on lighting while the switch trigger is being pulled.
The lamp goes out approximately 10 seconds after
releasing the trigger.
► Fig.6: 1. Lamp
NOTE: Use a dry cloth to wipe the dirt off the lens of
the lamp. Be careful not to scratch the lens of lamp, or
it may lower the illumination.
ASSEMBLY
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Removing the dust collector
CAUTION:
Never operate the tool without the
dust collector. Dust may come into your eyes and
cause eye injury.
To remove the dust collector, hold the tool handle and
pull back the tabs on the tool. Be sure to pull the tabs on
the both sides at the same time.
► Fig.7: 1. Tab
When installing, align the dust collector's edge with the
groove on the base.
► Fig.8: 1. Groove
Replacing drywall saw blade
CAUTION:
Always clean out all chips or for-
eign matter adhering to the blade and/or blade
holder. Failure to do so may cause insufficient tight-
ening of the blade, resulting in a serious personal
injury.
CAUTION:
Do not touch the blade or the
workpiece immediately after operation. They may
be extremely hot and could burn your skin.
CAUTION:
Make sure that the blade is prop-
erly secured. Insufficient tightening of the blade may
cause blade breakage or serious personal injury.
1. Remove the dust collector.
2. Remove the bolts on the blade holder with the hex
wrench.
► Fig.9: 1. Bolts 2. Blade holder 3. Blade
Max. cutting depth
30 mm
15 mm
8 ENGLISH
3. Set a new blade as shown in the figure. Make sure
that the curved edge of the blade points forward. Fit the
protrusion of the blade holder into the slot on the blade.
► Fig.10: 1. Slot 2. Protruded portion (opposite side)
4. Adjust the cutting depth then tighten the bolts.
5.
Attach the dust collector.
Installing snap-off blade
CAUTION:
Always use the snap-off blade with
designated length, width, and thickness. An inap-
propriately installed snap-off blade can be broken. A
broken blade can fly off and cause a personal injury.
A snap-off blade can also be used with this tool. Use 3
segments of 18 mm wide snap-off blade with 0.5 mm
thickness. The maximum cutting depth is 12.5 mm
when cutting a drywall.
► Fig.11: 1. Three segments of snap-off blade
1. Loosen the bolts on the blade holder. Turn the
blade holder so that its protrusion faces outward.
2.
Insert the snap-off blade so that the sharp edge
faces forward.
3. Secure the snap-off blade at the position where
the end of the first segment comes to the edge of blade
holder as illustrated.
► Fig.12: 1. Blade holder 2. End of the first segment
of snap-off blade 3. Allowable cutting length
Attaching blade cap
CAUTION:
Always attach the blade cap when
tool is not used. A bare blade may cause personal
injury or damage to the blade itself.
Pass the blade cap through the blade until the hook
catches the base cover. Note the direction of the blade
cap when attaching; the wider hook comes front side.
When removing the blade cap, lift it while pinching the
both sides.
► Fig.13: 1. Blade cap 2. Hook
During operation, insert the blade cap to the hook on
the base as illustrated until it clicks.
► Fig.14: 1. Blade cap 2. Hook
Hex wrench storage
When not in use, store the hex wrench as shown in the
figure to keep it from being lost.
► Fig.15: 1. Hex wrench
Connecting a vacuum cleaner
CAUTION:
Attach the blade cap before con-
necting vacuum cleaner.
Connect a Makita vacuum cleaner for clean operation.
Remove the rubber cap on the dust collector and con-
nect the vacuum cleaner's hose to the nozzle of the
dust collector.
► Fig.16: 1. Dust collector 2. Rubber cap 3. Vacuum
cleaner hose