Makita DHS782 Betriebsanleitung Seite 21

Troubleshooting for wireless activation function
Before asking for repairs, conduct your own inspection first. If you find a problem that is not explained in the manual,
do not attempt to dismantle the tool. Instead, ask Makita Authorized Service Centers, always using Makita replace-
ment parts f or repairs.
State of abnormality
T h e w ireless ac tiv ation lamp d oes
not ligh t/ blink.
Cannot finish tool registration / can-
celling tool registration successfully.
T h e v ac uum c leaner d oes not run
along w ith th e sw itc h operation of
th e tool.
T h e v ac uum c leaner runs w h ile th e
tool s switch trigger is not pulled.
Probable cause (malfunction)
T h e w ireless unit is not installe d into t h e tool.
The wireless unit is improperly installed
into th e tool.
T h e terminal of th e w ireless unit and / or
the slot is dirty.
T h e w ireless ac tiv ation button on th e
tool h as not been push ed .
The stand-by switch on the vacuum
c leaner is not set to " A U T O " .
No power supply
T h e w ireless unit is not installe d into t h e tool.
The wireless unit is improperly installed
into th e tool.
T h e terminal of th e w ireless unit and / or
the slot is dirty.
The stand-by switch on the vacuum
c leaner is not set to " A U T O " .
No power supply
I nc orrec t operation
The tool and vacuum cleaner are away
from each other (out of the transmission
range).
Before finishing the tool registration/
c anc ellation;
- th e sw itc h trigger on th e tool is pulled or;
- th e pow er button on th e v ac uum
c leaner is turned on.
T h e tool registration pro c e d ures f or t h e
tool or vacuum cleaner have not finished.
Radio disturbance by other appliances
which generate high-intensity radio waves.
T h e w ireless unit is not installe d into t h e tool.
The wireless unit is improperly installed
into th e tool.
T h e terminal of th e w ireless unit and / or
the slot is dirty.
T h e w ireless ac tiv ation button on th e
tool h as not been push ed .
The stand-by switch on the vacuum
c leaner is not set to " A U T O " .
More th an 1 0 tools are registered to th e
v ac uum c leaner.
T h e v ac uum c leaner erased all tool
registrations.
No power supply
The tool and vacuum cleaner are away
from each other (out of the transmission
range).
Radio disturbance by other appliances
which generate high-intensity radio
w av es.
O th er users are using th e w ireless
ac tiv ation of th e v ac uum c leaner w ith
th eir tools.
21 ENGLISH
Remedy
Install the wireless unit correctly.
Gently wipe off dust and dirt on the terminal of the
w ireless unit and c lean th e slot.
P ush th e w ireless ac tiv ation button on th e tool
briefly.
Set the stand-by switch on the vacuum cleaner to
" A U T O " .
Supply the power to the tool and the vacuum cleaner.
Install the wireless unit correctly.
Gently wipe off dust and dirt on the terminal of the
w ireless unit and c lean th e slot.
Set the stand-by switch on the vacuum cleaner to
" A U T O " .
Supply the power to the tool and the vacuum cleaner.
Push the wireless activation button briefly and perform
t h e tool registration / c an c ellation pro c e d ures again.
G et th e tool and v ac uum c leaner c loser to eac h oth er.
The maximum transmission distance is approximately
m however it may vary according to the circumstances.
Push the wireless activation button briefly and
perf orm th e tool registration/ c anc ellation proc ed ures
again.
P erf orm th e tool registration proc ed ures f or both th e
tool and th e v ac uum c leaner at th e same timing.
Keep the tool and vacuum cleaner away from the appli-
ances such as Wi-Fi devices and microwave ovens.
Install the wireless unit correctly.
Gently wipe off dust and dirt on the terminal of the
w ireless unit and c lean th e slot.
Push the wireless activation button briefly and make
sure th at th e w ireless ac tiv ation lamp is blinking in blue.
Set the stand-by switch on the vacuum cleaner to
" A U T O " .
P erf orm th e tool registration again.
I f more th an 1 0 tools are registered to th e v ac uum
c leaner, th e tool registered earliest w ill be c anc elled
automatically.
P erf orm th e tool registration again.
Supply the power to the tool and the vacuum cleaner.
G et t h e tool an d v a c uum c leaner c loser ea c h ot h er. T h e
maximum transmission distance is approximately
however it may vary according to the circumstances.
Keep the tool and vacuum cleaner away from the
appliances such as Wi-Fi devices and microwave
ov ens.
T urn of f th e w ireless ac tiv ation button of th e oth er
tools or c anc el th e tool registration of th e oth er
tools.
m