Operation - Makita DHS782 Betriebsanleitung

For tool with the inner ange for a
15.88 mm hole-diameter saw blade
(country specific)
Mount the inner flange with its recessed side facing
out w ar d onto t h e mounting s h a f t an d t h en pla c e c ir c u-
lar saw blade (with the ring attached if needed), outer
flange and hex bolt.
For tool without the ring
Fig.25: 1. Mounting s h a f t 2. Inner flange 3. C ir c ular
sa w bla d e 4. Outer flange 5. H e x bolt
For tool with the ring
Fig.26: 1. Mounting s h a f t 2. Inner flange 3. C ir c ular
sa w bla d e 4. Outer flange 5. H e x bolt
6. R ing
WARNING:
BE SURE TO TIGHTEN THE HE X
BOLT CLOCK W ISE SECURELY. Also be careful
not to tighten the bolt forcibly. Slipping your hand
from the hex wrench can cause a personal injury.
WARNING:
If the ring is needed to mount the
blade onto the spindle, always be sure that the
correct ring for the blade ' s arbor hole you intend
to use is installed between the inner and the outer
anges. Use of the incorrect arbor hole ring may
result in t h e improper mounting o f t h e bla d e c ausing
bla d e mo v ement an d se v ere v ibration resulting in
possible loss o f c ontrol d uring operation an d in seri-
ous personal injury.
Blade guard cleaning
When changing the circular saw blade, make sure to
also c lean t h e upper an d lo w er bla d e guar d s o f a c c u-
mulate d sa w d ust as d is c usse d in t h e Maintenan c e
se c tion. S u c h e f f orts d o not repla c e t h e nee d to c h e c k
lo w er guar d operation be f ore ea c h use.
Connecting a vacuum cleaner
When you wish to perform clean cutting operation,
connect a Makita vacuum cleaner to your tool. Connect
a hose of the vacuum cleaner to the dust nozzle as
shown in the figure.
Fig.27: 1. Dust nozzle 2. S c re w
Fig.28: 1. H ose 2. Va c uum c leaner

OPERATION

This tool is intended to cut wood products. With appro-
priate Makita genuine c ir c ular sa w bla d es, f ollo w ing
materials c an also be sa w e d :
• A luminum pro d u c ts
Refer to our website or contact your local Makita dealer
f or t h e c orre c t c ir c ular sa w bla d es to be use d f or t h e
material to be c ut.
Checking blade guard function
S et t h e be v el angle to 0 ° , an d t h en retra c t t h e lo w er
guard manually to the end and release it. The lower
guard is properly functioning if;
it is retracted above the base without any hindrance and;
—
it automatically returns and contacts with the stopper.
—
Fig.2 9 : 1. U pper guar d 2. L o w er guar d 3. Base
4. S topper 5. O pen 6. C lose
If the lower guard is not functioning properly, check if
sa w d ust is a c c umulate d insi d e o f t h e upper an d lo w er
guards. If the lower guard is not functioning properly
even after removing dust, have your tool serviced at a
Makita ser v i c e c enter.
Cutting operation
CAUTION:
W ear dust mask when performing
cutting operation.
CAUTION:
Be sure to move the tool forward
in a straight line gently. F or c ing or t w isting t h e tool
w ill result in o v er h eating t h e motor an d d angerous
kickback, possibly causing severe injury.
NOTE: When the battery cartridge temperature is
low, the tool may not work to its full capacity. At this
time, for example, use the tool for a light-duty cut for
a while until the battery cartridge warms up as high
as room temperature. T h en, t h e tool c an w ork to its
full capacity.
Fig.30
old the tool firmly. The tool is provided with both a front grip
an d rear h an d le. U se bot h to best grasp t h e tool. I f bot h h an d s
are holding saw, they cannot be cut by the circular saw blade.
S et t h e base on t h e w orkpie c e to be c ut w it h out t h e c ir c ular
saw blade making any contact. Then turn the tool on and wait
until the circular saw blade attains full speed. Now simply
mo v e t h e tool f or w ar d o v er t h e w orkpie c e sur f a c e, keeping it
flat and advancing smoothly until the sawing is completed.
To get clean cuts, keep your sawing line straight and your
speed of advance uniform. If the cut fails to properly follow
your intended cut line, do not attempt to turn or force the
tool back to the cut line. Doing so may bind the circular
saw blad e and lead to d angerous kic kbac k and possible
serious injury. Release switch, wait for circular saw blade
to stop and th en w ith d raw tool. R ealign tool on new c ut
line, and start c ut again. A ttempt to av oid positioning w h ic h
exposes operator to chips and wood dust being ejected
from saw. Use eye protection to help avoid injury.
Rip fence (Guide rule)
CAUTION:
Make sure that the rip fence is
securely installed in the correct position before
use. Improper attachment may cause dangerous
ki c kba c k.
Fig.31: 1. Rip fence (Guide rule) 2. C lamping s c re w
The handy rip fence allows you to do extra-accurate
straight cuts. Simply slide the rip fence up snugly
against t h e si d e o f t h e w orkpie c e an d se c ure it in posi-
tion w it h t h e c lamping s c re w on t h e f ront o f t h e base. I t
also makes repeate d c uts o f uni f orm w i d t h possible.
17 ENGLISH