General Operation - AEG CDP 4201 MP3/VCD Bedienungsanleitung

Headphones - Remote Control (ABB. 3)
A. PHONES
B. HOLD OFF/ON
C. PLAY/PAUSE
D. VOLUME
E. STOP/OFF
F. I BACK
G. I NEXT
H. ESP/LR/DIR
Note: Some keys are to be found both on the device
itself and on the remote control. Keys with the same
designation have the same function.
In order to use the headphone remote control, please
proceed as follows:
Connect the plug of the headphone remote control to the
socket (11) on the device and then insert the plug of the
headphones/earphones into the connection socket (A).
Messages in the Display (ABB. 4)
1 VCD / MP3 / CD Format
2 Track number
3 Playing time
4 Button lock display
5 ESP function
6 Battery replacement display
7 RAN - RANDOM function
8 PGM - PROGRAMM function
9 REP - Single repeat
10 REP ALL - All repeat
11 REP DIR - Album repeat
Initial Use of the Device
Inserting the Batteries (not supplied)
• Open the battery compartment (17) on the back.
• Insert two 1.5 V batteries of type AA. Ensure the
correct polarity (see the bottom of the battery compart-
ment or the imprint on the outside).
• If the device is not used for a prolonged period, please
remove the batteries in order to avoid the leakage of
battery acid.
• A battery symbol in the display indicates that the bat-
teries need to be replaced. Always replace a complete
set of batteries and not just one.
Note: Batteries should not be disposed of in the domestic
waste. Please return used batteries to the appropriate
collection points or the dealer where you bought them.
Batteries must never be thrown into a fi re.
05-CDP 4201 NEU4 AEG 53
Batteries in the Remote Control
The battery in the remote control is a long-life lithium cell. If
the range of the remote control decreases, please proceed
as follows:
• Open the battery compartment on the side of the
remote control.
• Replace the cell with a battery of the same type.
Ensure the correct polarity.
• Close the battery compartment.
Mains Operation
It is possible to operate the device using the mains power
unit.
1. Insert the plug of the power unit into a correctly
installed 230V, 50 Hz wall socket.
2. Connect the CD player to the power unit by inserting
the plug of the power unit into the DC 4.5 V socket.
3. When using a power unit (DC 4.5V/700mA) ensure the
correct polarity according to the inscriptions on the CD
player.
Car Operating Mode
Thanks to the adapter cassette and the cigarette lighter
adapter the CD player can be used on your car radio with
the cassette adapter.
1. Insert the cigarette lighter adapter in the cigarette
lighter and the jack at the end of the cable into the
4.5V/DC socket of the CD player.
2. Insert the jack of the adapter cassette into the AV OUT
socket (12) of the CD player.
3. Switch on your car radio and insert the adapter casset-
te into the cassette deck. Make sure that the connector
cable of the adapter cassette is inserted correctly into
the cassette slot! The cassette mechanism may jam!
Some car radios may eject the adapter cassette immediate-
ly after inserting it. In this case fi t the cassette's connector
cable along the slot and insert the cassette turned over on
the other side. If the car radio ejects the adapter cassette
again, the adapter cassette cannot be used.

General Operation

AUDIO/ Switches between loudspeaker set-
tings: MONO L, MONO R, STEREO
(only in VCD mode).
EQ (4): Various sound modes are available
(CLASSIC, DISCO, POP, JAZZ).
CHARGE
ON/OFF (16): Switches on the charge function
when the external power unit is
connected.
53
05.09.2005, 12:06:56 Uhr