Delivery Contents; About This Product - Aventics AS1 Betriebsanleitung

AVENTICS | AS1 / AS2 / AS3 / AS5 | R412013436–BAL–001–AE | English
Intended use
The product is exclusively intended for installation in a machine
or system or for combination with other components to form
a machine or system. The product may only be commissioned
after it has been installed in the machine/system for which
it is intended.
Use is permitted only under the operating conditions and within
the performance limits listed in the technical data. Only use
compressed air as the medium.
The product is technical equipment and is intended for
professional use only.
Intended use includes having read and understood this
documentation, especially the chapter "Notes on Safety".
Personnel qualifications
All tasks associated with the product require basic mechanical,
pneumatic and electrical knowledge, as well as knowledge of the
respective technical terms. In order to ensure operational safety,
these tasks may only be carried out by qualified personnel or an
instructed person under the direction of qualified personnel.
Qualified personnel are those who can recognize possible hazards
and institute the appropriate safety measures, due to their
professional training, knowledge, and experience, as well as their
understanding of the relevant regulations pertaining to the work to
be done. Qualified personnel must observe the rules relevant to the
subject area.
General safety instructions
W
Observe the valid local regulations in the country of use to
protect the environment and avoid workplace accidents.
W
Only use AVENTICS products that are in perfect working order.
W
Examine the product for obvious defects, such as cracks in the
housing or missing screws, caps, or seals.
W
Do not modify or convert the product.
W
Persons who assemble, operate, disassemble, or maintain
AVENTICS products must not consume any alcohol, drugs,
or pharmaceuticals that may affect their ability to respond.
W
The warranty will not apply if the product is incorrectly
assembled.
W
Do not place any improper mechanical loads on the product
under any circumstances.
W
Product warnings and information must be legible,
i.e. not covered by paint, etc.
Safety instructions related to the product
and technology
W
Lay cables and lines so that they cannot be damaged and
no one can trip over them.
W
Do not operate the product in aggressive ambient air or allow
it to come into contact with aggressive media.
The substances listed as examples in the following table,
which contain solvents in various concentrations, can lead to
an aggressive ambient air/compressed air in the application
area of compressed air preparation devices and in the suction
area of air compressors.
Solvents: Acetone, paint thinners, alcohols, ester
Detergents: Trichloroethylene, perchlorethylene,
benzene, gasoline
Other media: Synthetic oils, drilling oil, high-alloyed oils,
certain compressor oils, brake fluid,
ammonia, bonding and sealing agents,
plasticizers, anti-freeze, coolants/
lubricants
A pressurized polycarbonate reservoir may corrode
in an aggressive ambient air/compressed air and explode
as a result.
If the presence of the substances stated in the table cannot
be avoided, such as in gluing machines or vulcanization
plants, the use of metal reservoirs is required.
W
If a lubricator is used, please only use a suitable pneumatic oil,
see online catalog (www.aventics.com/pneumatics-catalog).
W
No soiling may be allowed to collect on or in the filters,
reservoirs or windows. Replace reservoirs if soiling cannot
be removed from the drain (drain may become clogged).
Also observe the "Customer information on material
resistance in compressed air preparation"
(MNR R412025273).
3

Delivery Contents

The delivery contents include:
W
1 filter (pre, micro, active carbon-) as ordered
W
Operating instructions
4

About this product

Standard filter FLS, pre-filter FLP, micro-filter FLC and active
carbon filter FLA are components of maintenance units:
W
Standard filter FLS: Solid impurities and condensate are
removed from the compressed air by centrifugal force
and filtration.
W
Pre-filter FLP and micro-filter FLC: Suitable for very high
standards in compressed air purity.
W
Active carbon filter FLA: Filters out odors from the compressed
air. The oil vapor molecules in the compressed air are absorbed.
6