Table of Contents / Inhalt Table of Contents / Inhalt English Security instructions Symbols General security instructions General device description Delivery content Connectors and interfaces User interface: LEDs Identify button: Identification & Reset General remarks Transport Unpacking Warranty regulations Maintenance and Repair Disposal Support Installation...
Seite 4
Table of Contents / Inhalt Product specifications Certifications Deutsch Sicherheitshinweise 10.1 Symbole 10.2 Hinweise Gerätebeschreibung 11.1 Lieferumfang 11.2 Anschlüsse und Schnittstellen 11.3 Benutzeroberfläche: LEDs 11.4 Identify-Taster: Identifikation & Reset Allgemeine Hinweise 12.1 Transport 12.2 Entpacken 12.3 Garantiebestimmungen 12.4 Reparatur und Wartung 12.5 Entsorgung 12.6...
Seite 5
Table of Contents / Inhalt Zertifizierung Dimensions / Abmessungen...
Connect cables and data only when the device is powered down. The device must be supplied by a separate certified SELV Class 2 power supply. The maximum length of each connected cable is 30 m. If safety instructions are missing, please contact OSRAM to receive a new copy.
SYMPHOLIGHT. Connections between servers, Cores and Nodes are always made with e:net via Ethernet. The e:cue SYMPL serial Node is a two-channel serial interface for use with e:cue’s lighting control solution SYMPHOLIGHT. It provides two independent serial interfaces, one RS-232 and one RS-485 channel. The e:cue SYMPL serial Node is powered by an external power supply or via Ethernet PoE.
General device description Connectors and interfaces View from top RS-485 interface (GND, –, + left to right) RS-232 interface (GND, Rx, Tx left to right) RS-485 status LED RS-232 status LED Error LED e:net LED (Ethernet, LAN activity) Status LED (Device status) Identify button Power supply (Vcc+, Vcc–...
Switch the device off and on. If the error persists, check the wiring or contact OSRAM Service. Status + The Status and Error LED blink simultaneously to Error identify the SYMPL Node (enabled “Identify Interface...
Only transport the device in its original packaging. This protects the device from damage. Unpacking Only unpack the e:cue SYMPL serial Node at its installation location. To protect the device against condensation water, unpack it and wait until all moisture remaining in the device has evaporated. Condensation can occur when the device is moved from a cold to a warm location.
Before dismounting, appropriate measures must be taken to protect the respective components against damage caused by electrostatic discharge (ESD protection). Do not try to repair the device. Return it to your OSRAM distributor for replacement or repair. Disposal The proper disposal of packing materials and of the device is the responsibility of the respective user and for his account;...
Installation Installation The installation of the SYMPL serial Node consists of mounting the device, connections to e:net, to power supply, and of devices to the serial ports. The sequence of cabling is not defined. Supply the SYMPL serial Node with power after all cabling is completed;...
RS-232: from left to right: GND, Rx, Tx RS-485: from left to right: GND, -, + It is recommended to use twisted pair cabling. Power supply The e:cue SYMPL serial Node can be powered by an external power supply or via Power-over-Ethernet.
24 V DC to the SYMPL serial Node. Network configuration The configuration of the e:cue SYMPL serial Node is done via e:cue SYMPHOLIGHT. See the SYMPHOLIGHT System Manual for details on configuration, available at www.ecue.com.
Network configuration Default network properties The SYMPL serial Node has as factory setting the default IP address 192.168.123.1. DHCP is enabled by default. To change the network configuration use either SYMPHOLIGHT or the web interface of the SYMPL serial Node: Network configuration with SYMPHOLIGHT Open the context menu of the SYMPL serial Node in the Setup tab of SYMPHOLIGHT by a right-click on the device.
Network configuration Network configuration with the web interface Open a common web browser on a connected PC. Enter the SYMPL serial Node's IP address into the address bar: e.g. http://192.168.123.1 The web interface of the SYMPL serial Node is displayed: Click “Configure”...
SYMPL serial Node or click the Update button in the head toolbar. Dismounting Disconnect all attached cables. Dismount the e:cue SYMPL serial Node from the rail by pulling the black DIN rail handle and unhitching the SYMPL Node. The dismounting is completed.
Product specifications Product specifications Product number AB444220035 Dimensions (W x H x D) 53.5 x 90.5 x 62 mm 0.76 x 0.30 x 0.20 in (without fastening clip) Weight 100 g Power supply input 24 V DC on screw terminal wire gauge: 0.25 ...
3-pin terminal plug RS-485 short circuit protected: = 112mA, thermal shutdown Certifications e:cue SYMPL serial Node is certified according to EN 55022, EN 55024, 62368-1 Ed. 2 Conforms to ANSI / UL Std. 60950-1 4000805 Certified to CSA Std. C22.2 NO. 60950-1...
Das Gerät muss durch ein separates Class 2-Netzteil versorgt werden. Die maximale Länge jedes angeschlossenen Kabels beträgt 30 m. Sollte das beigelegte Heft mit den Sicherheitshinweisen fehlen, wenden Sie sich bitte an den OSRAM-Service für ein zusätzliches Exemplar.
Verbindungen zwischen Servern, Cores und Nodes erfolgen immer über e:net mittels Ethernet. Der e:cue SYMPL serial Node ist ein Interface mit zwei seriellen Schnittstellen für die e:cue Steuerungslösung SYMPHOLIGHT. Er bietet ein RS-232- und ein RS-485-Interface. Mit Spannung versorgt wird der SYMPL serial Node von einem externen Netzteil oder über Power-over-...
Gerätebeschreibung 11.2 Anschlüsse und Schnittstellen Sicht von oben auf das Gerät RS-485-Schnittstelle (GND, –, + links nach rechts) RS-232-Schnittstelle (GND, Rx, Tx links nach rechts) LED RS-485-Status LED RS-232-Status LED Fehler (Error) LED e:net (Ethernet, LAN-Aktivität) LED Status (Gerätestatus) Identifikations-Taster Stromversorgung (Vcc+, Vcc–...
Fehler wie Kurzschluss der Datenanschlüsse. Schalten Sie das Gerät aus und wieder ein. Besteht der Fehler weiterhin, überprüfen Sie die Verdrahtung oder wenden Sie sich an den OSRAM Service. Status + Die Status- und die Error-LED blinken simultan, um Error den SYMPL Node zu identifizieren (aktiver “Identify...
Auspacken, bis das Gerät die Temperatur am Installationsort angenommen hat. Bewahren Sie die Verpackung für einen späteren Transport auf. Überprüfen Sie die Vollständigkeit des Lieferumfanges nach Kapitel „12.1 Lieferumfang“ auf Seite 23. Sollten Komponenten beschädigt sein oder fehlen, wenden Sie sich an Ihren OSRAM Support Service.
Die Garantie- und Gewährleistungsbestimmungen finden sich in der Regel im Angebot und in der Auftragsbestätigung. Zusätzlich sind Informationen dazu auf der OSRAM- Website www.osram.de unter “Services” “OSRAM Garantien” aufgeführt. Gesetzlich geregelte Garantiebedingungen sind davon unberührt. 12.4 Reparatur und Wartung Dieses Gerät erfordert keine Wartung.
+49 (5251) 54648-0 support@ecue.com 13 Installation Zur Installation vom e:cue SYMPL serial Node montieren Sie diesen auf einer Hutschiene und schließen die Spannungsversorgung, eine e:net- Verbindung und Geräte an die serielle Schnittstelle an. Die Reihenfolge der Kabelanbindung ist beliebig. Schalten Sie die Stromversorgung erst an, wenn alle Kabel angeschlossen sind.
Installation Empfohlener vertikaler 160 mm Hutschienenabstand: (mit 40 mm-Kabelkanal) Installationsort Innen (im Gebäude) 13.2 Montage Der SYMPL Node wird auf einer 35 mm-DIN-Hutschiene vertikal montiert (EN 60715). 1. Hängen Sie das Gerät oben in die Hutschiene ein. 2. Drücken Sie leicht auf das Gehäuse, so dass die untere Verriegelung auf der Hutschiene einrastet.
Schließen Sie bei der Verwendung von PoE nur einen Ethernet-Anschluss von einem PoE-Versorger (Midspan-/Endspan-Device) an. Externes Netzteil: Verbinden Sei den e:cue SYMPL serial Node mit einem NEC Class 2 24 V DC Netzteil. Das Anliegen von Stromversorgung am Node entspricht einem Anschalten des Gerätes.
Class 2-Netzteil im Schaltschrank für die 24 V-Gleichspannungsversorgung. 14 Netzwerk-Konfiguration Die Konfiguration des e:cue SYMPL serial Node erfolgt über e:cue SYMPHOLIGHT. Im SYMPHOLIGHT-Benutzerhandbuch finden Sie weitere Details. Das Benutzerhandbuch ist auf www.ecue.com verfügbar. Die Netzwerkeinstellungen des SYMPL serial Nodes sind voreingestellt. Um Änderungen an den Netzwerkeinstellungen vornehmen zu können, ist die...
Netzwerk-Konfiguration Änderungen der Netzwerkeinstellungen können entweder in SYMPHOLIGHT oder über die Webschnittstelle des SYMPL serial Nodes vorgenommen werden: 14.2 Netzwerkeinstellung über SYMPHOLIGHT Öffnen Sie in dem Setup Tab von SYMPHOLIGHT das Kontextmenü von dem SYMPL serial Node mit einem Rechtsklick auf das Gerät.
Netzwerk-Konfiguration 14.3 Netzwerkeinstellung über die Webschnittstelle Öffnen Sie auf einem verbundenen PC einen gewöhnlichen Webbrowser. Geben Sie in der Adressleiste die IP-Adresse des SYMPL serial Nodes ein: z.B. http://192.168.123.1. Die Webschnittstelle des SYMPL serial Nodes wird angezeigt: Klicken Sie “Configure”. Die Einstellungs-Seite wird angezeigt: Legen Sie die Netzwerkeinstellungen unter der Rubrik “Device Basics”...
Knopf in der oberen Werkzeugleiste. 16 Demontage Um den e:cue SYMPL serial Node abzubauen, trennen Sie alle verbundenen Kabel und Anschlüsse von dem Gerät. Entfernen Sie den SYMPL serial Node von der Hutschiene, indem Sie die schwarze Hutschienen-Entriegelung ziehen und das Gerät von der Hutschiene lösen.
Produktdaten Vor der Demontage müssen geeignete Vorsichtsmaßnahmen ergriffen werden, um die entsprechenden Komponenten vor Schäden durch elektrostatische Entladung zu schützen (ESD-Schutz). 17 Produktdaten Bestellnummer AB444220035 Abmessungen (B x H x T) 53,5 x 90,5 x 62 mm (ohne Befestigungsclip) Gewicht 100 g Stromversorgung 24 V= auf Schraubanschluss...