Regulatory Information; Specifications; Maintenance Tips - Interlogix TX-6310-03-1 Bedienungsanleitung

Control panel does not respond:
•
Move or rotate the CO alarm position.
•
Make sure the CO alarm is properly enrolled into the
control panel.
•
Make sure that you are using a compatible control panel
(see "Specifications" below).
Tamper condition does not restore:
•
Make sure the CO alarm body is properly installed on the
mounting plate.
•
Make sure there are no trouble indications at the CO
alarm.
•
Make sure that you are using an Interlogix 868AM Gen2
control panel or repeater.
If a tamper alarm occurs:
•
Make sure that you are using an Interlogix 868AM Gen2
control panel or repeater.
•
Make sure that the control panel is in sensor test mode
during sensor testing.
Alarm/open condition does not restore:
•
Make sure that the CO alarm condition has cleared at the
CO sensor.
•
Make sure that you are using an Interlogix 868AM Gen2
control panel or repeater

Specifications

Power Three AA batteries
Battery type 1.5 VDC alkaline
Required batteries Duracell MN 1500
Sensor Electrochemical
Type B
Battery Life 1 year (minimum)
Sensor life 10 years
Frequency 868AM Gen2
Wireless operating 868.000 MHz - 868.600 MHz
frequency
Maximum power output 14 dBm
Simon XT EMEA FW v5.3 or higher
ATS1235 (ATS Master FW v2.3 or higher
and ATS Advanced
Receiver)
NX-848E, NX-848E-BO Radio module FW v4.43 or higher
and NX-10 Series Panels
Repeaters TX-9001-03-1 All FW versions
and NX-848E-RP
Supervisory interval 20 minutes
Audible alarm Temporal 4
Alarm response times 50 PPM = 60 to 90 min
100 PPM = 10 to 40 min
300 PPM = 3 min or less
Dimensions 119 x 70 x 47 mm
−20 to +60°C
Storage temperature
P/N 3102145 (ML) • REV F • ISS 11MAR19
Operating environment:
Temperature 0 to +40°C
Relative humidity 10 to 95% noncondensing

Regulatory information

Manufacturer Placed on the market by:
UTC Fire & Security Americas Corporation, Inc.
3211 Progress Drive, Lincolnton, NC, 28092, USA
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, Netherlands
Made in China
Certification
EN EN 50291-1:2010
Product warnings THESE PRODUCTS ARE INTENDED FOR SALE
and disclaimers TO AND INSTALLATION BY QUALIFIED
PROFESSIONALS. UTC FIRE & SECURITY
CANNOT PROVIDE ANY ASSURANCE THAT
ANY PERSON OR ENTITY BUYING ITS
PRODUCTS, INCLUDING ANY "AUTHORIZED
DEALER" OR "AUTHORIZED RESELLER", IS
PROPERLY TRAINED OR EXPERIENCED TO
CORRECTLY INSTALL FIRE AND SECURITY
RELATED PRODUCTS.
For more information on warranty disclaimers and
product safety information, please check
https://firesecurityproducts.com/policy/product-
warning/
European Union UTC Fire & Security hereby declares that this
directives device is in compliance with the applicable
requirements and provisions of all applicable rules
and regulations, including but not limited to the
Directive 2014/53/EU. For more information see:
www.utcfssecurityproducts.eu
2012/19/EU (WEEE directive): Products marked
with this symbol cannot be disposed of as
unsorted municipal waste in the European Union.
For proper recycling, return this product to your
local supplier upon the purchase of equivalent
new equipment, or dispose of it at designated
collection points. For more information see:
www.utcfssecurityproducts.eu/recycle/
This product may contain a battery that cannot be
disposed of as unsorted municipal waste in the
European Union. See the product documentation
for specific battery information. The battery is
marked with this symbol, which may include
lettering to indicate cadmium (Cd), lead (Pb), or
mercury (Hg). For proper recycling return the
battery to your supplier or to a designated
collection point. For more information see
www.utcfssecurityproducts.eu/recycle/

Maintenance tips

To keep your alarm in good working order:
• Perform a CO sensor test once a week (see "Normal CO
alarm test" on page 4).
•
Vacuum the alarm cover once a month to remove
accumulated dust.
•
Never use detergents or solvents to clean the alarm.
Chemicals can permanently damage or temporarily
contaminate the alarm.
0359
or scan the QR code.
5 / 25