YATO YT-82830 Bedienungsanleitung Seite 17

GB
fi ed by the manufacturer, such as blades, cutting discs or discs equipped with the cutting chain. Do not substitute the cutting line
with a metal wire or string. The use equipment other than those specifi ed may result in a serious threat to the safety of the operator
and bystanders. Prior to installation of the cutting element and cover to make sure that they are not damaged, have no cracks, are
not bent. Make sure, that there is at least 1 meter line on the spool.
During operation, it is likely, that objects can be thrown towards the operator and bystanders. The operator is responsible for
accidents or a threat presented to others or to the environment. Do not operate the device, if there are bystanders in the vicinity,
especially children and animals. Prior to work appoint a safety zone with a radius, of at least 15 meters from the place of work.
Despite the safety measures taken during the design and construction of the machine, there always remains a residual risk.
Therefore, you should use the technical and complementary protective measures.
Always wear eye and face protection, this protects the eyes, face and respiratory system against dust and objects thrown during
the operation. Always wear the correct, adjacent to the body, protective clothing. Use only long trousers. Do not wear loose cloth-
ing or jewelry. which can be caught by moving parts of the machine. Wear protective gloves and hearing protection. Wear safety
shoes with non-slip soles, does not work with bare feet or sandals.
The device must be regularly reviewed in accordance with the information contained in the following section. This will allow for
more effi cient and safer operation.
When you work you should use hearing protectors. Exposure to excessive noise can lead to permanent hearing damage.
Use protective glasses. During the work the garbage can create risk of eye injury.
You must be familiar with the instructions to switch off the device in case of emergency.
Before the work always check whether the cutting element, screws, guards and other elements are not worn or damaged. Replace
worn parts before starting work. You should also check that the screw connections not loosened. Tighten the loose bolts.
During operation, you should not tilt the machine and keep it constantly in a state of equilibrium, you should always put your feet
surely on the slope and walk, never run. When mowing slopes you should always move across the slope, never along.
Never touch the dangerous moving parts before disconnecting the machine from the power supply and until all dangerous moving
parts completely stop.
The cutting element can rotate for some time after the engine is stopped.
Disconnecting the machine from the power supply is to turn off the machine switch and disconnect the power source. Unplugging
the power cord from the wall socket in the case of mains-operated devices or disconnect the battery in the case of battery-powered
devices.
The machine should be disconnected from the power supply in every case when:
- the operator walks away from the machine,
- the obstruction is removed,
- before checking or cleaning,
- before the inspection whether machine is damaged after hitting the foreign object,
- before the immediate testing after the machine starts to vibrate excessively.
PRODUCT SERVICE
Preparation of grass trimmer to work
Attention! Before all mounting and regulatory operations, you should disconnect the grass trimmer from the power supply. Remove
the battery pack from the power tool socket!
Visually inspect the tool, If you notice any damage, do not start any work before repairing them.
Installation of the front handle (II)
If the handle has not been fi tted, then you should translate the holder through the guard of power cables, and, after that, lock its
position with the lever.
The handle position should be selected in an experimental way, to fi t the physical condition of the operator and the area in which
the trimmer will be used. The handle position should allow work with the hands bent at the elbows and straight back. It should also
ensure the freedom of movement in the plane of trimmer work.
Installing the cutting element guard (III)
Insert the shield latches in the trimmer cover, and then protect them by a screw.
At the edge of the guard there is a blade, which is used to automatically shorten the line. Before starting work, you should remove
from it the guard.
Adjustment operations
In addition to adjusting the position of the front handle, the trimmer allows to adjust the length of the power supply wires, turn of
the lower part of the power supply wires, rotation of the cutting head, and adjustment of the cutting width.
It is possible to use stepless setting of the length of the power cord cover, which translates into the length of the entire tool. Turn
the ring (V) in the direction of the symbol of an open padlock, adjust the length and rotate the ring in the direction of the closed
padlock symbol. Make sure, that the length of the trimmer does not changed spontaneously during work.
O R I G I N A L I N S T R U C T I O N S
17