Using The Plug-In Charger; Battery Packs And Batteries; Setting Up Components / Function Test; Power Supply - Babyfon BM 1000S Bedienungsanleitung

GB
Never use caustic detergents to clean the devices as these could damage the plastic
surfaces.
Clean the devices with a dry or slightly moist cloth.
3.5

Using the plug-in charger

Connect the device only to a correctly installed mains socket with voltage which
corresponds to that given on the nameplate of the plug-in charger.
Make sure that connecting cable is not positioned so that people could trip over it.
Make sure that the connecting cable is not pinched, crushed or stretched.
When using an adapter or an extension cable, make sure that these comply with
valid safety regulations. The maximum current given must not be exceeded.
Continuous operation with the plug-in charger may damage your battery packs.
After charging the battery packs, disconnect the plug-in charger from the BABYFON
® BM 1000 S.
3.6

Battery packs and batteries

Keep battery packs and batteries away from children.
Do not try to charge used, non-rechargeable batteries.
Batteries and battery packs must not be thrown away with domestic rubbish.
As a consumer you are legally obliged to return used batteries/battery packs, regardless
of whether or not they contain harmful substances. You can hand them in at your nearest
collection point or wherever batteries/battery packs of the kind concerned are sold. We
also take back batteries/battery packs free of charge.
If you wish to return your old batteries to us, please send them marked "Used!" to the
following address:
Vivanco GmbH, Ewige Weide 17, D-22926 Ahrensburg

4. Setting up components / function test

N.B.: Before inserting the battery packs supplied or connecting to the mains power
supply, switch off the devices.
Note: To protect the display A5 from scratching during the manufacturing process a
transparent film is attached. Remove this film.
4.1

Power supply

To insert or replace the battery packs:
1. To insert and remove the battery packs the device should always be switched off and
disconnected from the plug-in charger D. To switch off, press the On/Off button A4
for approx. 2 seconds.
2. Slide the lid of the battery pack compartment A12 down.
3. Place the 4 supplied battery packs in the battery pack compartment.
N.B.: Battery packs must be inserted with their plus and minus poles (+/-) positioned
exactly as marked on the bottom of the battery pack compartment.
Note: New battery packs must first be charged for at least 15 hours with the device
switched off before they are ready to function. The charging of battery packs is described
in Chapter 6.2 "Charging the battery packs".
4. Slide the lid back up until it clicks into place.
24
GB
4.2

Switching on and basic setting

1. Press the On/Off button A4 for approx. 2 seconds. The devices are now switched on
and the display A5 lights up briefly. Then the basic display appears.
In this basic setting the devices function as normal radio devices.
2. Check that the same channel indicator B10 (example: "01") appears on both devices.
The same subcode B9 (example: "01") must also be set on both devices.
N.B.: In all operating modes the transmitter and receiver can only communicate if
these two settings are identical on both devices. To change these settings,
please read Chapter 5.3 "Setting the channel and subcode".
4.3

Function test

Ideally, the function test should be conducted by two people:
1. Press the On/Off button A4 for approx. 2 seconds, thereby switching on both devices.
If there is a loud whistling noise the two devices are standing too close together.
2. Take one of the devices into another room.
3. Press the Talk button A2 on the transmitter and speak into the microphone A10.
The transmission symbol B13 indicates that transmission is taking place.
The reception symbol B14 appears in the display on the receiver and the spoken text
is transmitted.
If the receiver cannot hear anything, check the individual points in Chapter 8
"Troubleshooting".
5

Adjusting the devices for operation

Note: Before adjusting the devices to suit your requirements it is often advisable to
perform a reset. This resets all settings to the default setting, ensuring that you have a
safe basis to begin making your setting adjustments.
New devices already have the default settings.
5.1

Reset function

1. Switch off the device by pressing the On/Off button A4 for approx. 2 seconds.
2. Disconnect the AC adapter D, but leave the battery packs inside the device.
3. Press the "UP" A7, "MODE" A6 and "Talk" A2 buttons simultaneously
4. Switch the device back on while continuing to hold the buttons down.
5. As soon as all the values are displayed simultaneously in the display A5, release the
buttons.
6. Confirm the reset by pressing any button. The device switches itself off again. All
memories are now erased and reset to the default setting.
5.2

Setting the application

The BABYFON ® BM 1000 S allows you use each individual device either as a Babyfon
or as a radio device (PMR). Despite this scope it is easy to set the required application by
making just a few adjustments. The following table shows you the different application
and combination possibilities offered by your Babyfon:
To use as a Babyfon, activate one of these two variants
Device 1
Transmitter
Device 2
Receiver Function
Babyfon without range control
Babyfon with range control
25