Setting The Channel And Subcode; Keylock; Transmitter (Baby) - Babyfon BM 1000S Bedienungsanleitung

GB
To use as a normal radio device (PMR), activate this variant
Device 1
Transmitter/
receiver
To set the selected menu item on a device, proceed as follows:
1. Switch on the devices by pressing the On/Off button A4 for approx. 2 seconds.
2. Press the Mode button A6 and hold it down.
3. Using the Selection buttons (DOWN/UP) A7 you can now select the appropriate
menu item.
4. Then release the Mode button A6 and you will see the corresponding symbol in the
display. The selected menu item is now activated.
Make sure that the transmitter and the receiver have the same setting for the
channel and the subcode (see Chapter 5.3 "Setting the channel and subcode").
Example of channel and subcode setting
5.3

Setting the channel and subcode

N.B.: The transmitter and receiver can only communicate if the channel and security
code are identical on both devices.
By combining 8 channels with 38 subcodes you have numerous possibilities to
prevent interference.
Setting the channel
You have a choice of 8 channels. Each channel is allocated a particular frequency in the
radio frequency range. If there is too much interference on the selected channel, select
another one, making sure that you select the same channel for both devices.
Setting the personal security code
You have the option of using 38 different subcodes (CTCSS = Continuous Tone Code
Squelch System) for each transmission channel. This enables you to protect yourself
against the reception of external radio transmissions on the same channel. If you can hear
external radio signals or interference on the set channel, select another subcode to
prevent this. You can also switch off the subcode (00) to hear all transmissions on the set
channel.
26
Device 2
Transmitter/
receiver Function
PMR radio device (walkie-talkie)

Transmitter (baby)

Receiver (parents)
Receiver (parents) with range control
Radio device (PMR)
GB
1. Switch on the devices. To do so, press the On/Off button A4 for approx. 2 seconds.
The display A5 lights up briefly and the symbols appear.
2. Press the mode button (MODE) A6 once. The channel indicator B10 begins to flash.
3. Set the required channel (0 - 8) using the selection buttons (DOWN/UP) A7.
4. Confirm the setting by pressing the mode button (MODE) A6. At the same time you
exit the setting mode and skip to the setting of the subcode.
5. The indicator for the subcode B9 begins to flash.
6. Using the selection buttons (DOWN/UP) A7, set the required subcode (00 - 38).
7. Confirm the subcode by pressing the confirmation button (OK) A8 and exit the setting.
5.4

Keylock

When the keylock is activated all the keys are locked. The settings can now no longer be
changed, e.g. if a child gets hold of the device and plays with it or if you carry the device
in your pocket. This prevents operating errors.
1. To switch on the keylock, press the confirmation button (OK) A8 for approx. 3 seconds
until the keylock symbol B6 appears in the display.
2. To switch off the keylock, press the confirmation button (OK) A6 for approx. 3
seconds until the keylock symbol B6 disappears again.
5.5 Transmitter (baby)
This function sets the BABYFON ® BM 1000 S as the transmitter and transmits the
sounds made by your child. To set this function, see 5.2 "Setting the application".
To avoid disturbing the child the speaker is deactivated in this setting.
Hands-free function (VOX)
The transmitter is fitted with a hands-free function (VOX) which is activated automatically
in this setting. This means that the transmitter (baby) does not begin to transmit until a
certain minimum noise level is reached, e.g. when your child shouts or cries. This has
several advantages:
no transmission radiation in standby mode
no constant noise level in the receiver
power-saving
Low
Setting the response sensitivity
With the response sensitivity you set the volume at which the transmitter is activated and
begins to transmit sound to the receiver. There are several settings available. Find the
Mid best setting by trial and error.
Press the selection buttons (DOWN/UP) A7 to adjust the response sensitivity. In the
display the sensitivity indicator B8 shows the current setting.
On the transmitter the transmission indicator B13 lights when the device is activated and
Hi
transmitting.
Using the additional microphone
An additional microphone is included in the set. You can use it in the transmitter setting;
it provides the following benefits as you can place the microphone closer to the baby:
higher sensitivity, therefore less background noise
improved hands-free function
improved transmission quality
response sensitivity can be more finely adjusted
Connect the plug C4 of the additional microphone included to the socket A13 of the
device set as the transmitter.
Attach the microphone C3 by the clip C2 and the Velcro strap to the cot so that the
microphone is pointing towards the baby.
N.B. Make sure the microphone is attached where the baby cannot reach it.
27