Klippan CENTURY Bedienungsanleitung Seite 11

INSTRUCTION MANUAL
1. Pull out the internal belt to full extent, by pushing button (A) and pulling the shoulder belts (B).
2. Release the shoulder belt pipe from the back of the seat, move the pipe to the new height and replace the pipe,
push one end of the pipe into the mount and then press the other end of pipe into the other mount.
3. The shoulder straps should be at the same level as the lower part of the head support.
4. Pull the handle and adjust the height of the headrest.
PREPARATIONS TO MOUNT THE SEAT INTO THE CAR
5. Attach the lower tether straps to the rails on the front seat of the car if the strap can be threaded between the
floor and the rail.
6. Mounting of the lower tether straps on the sides of the backseat.
7. Lower tether straps can be mounted to the backrest of the front seat.
8. If there are no attachment points in the car, you can use our additional attachement loops. These can be
fastened into the car. Klippan item number for these 150-55-706.
9. Check beneth the car seat if you can use existing bolts for mounting the additional attachement loops.
10. Mounting the lower tether straps on the sides of the backseat, using attachement loops.
11. Place the child seat on the seat of the car. Adjust the reclining on the recline-tube by pulling the adjustment
button (1). Pull out the leg, and lock the button (2).
12. Turn out the load-leg against the stopper (1). Adjust the length on the load-leg by pulling out the red button
on the side (2). Check that the load-leg is properly against the floor of the car, and that the load-leg is properly
locked (3).
13 Pull out completely the cars 3P seat belt, thread the belt throug the blue mounting hooks on the child seat.
14 Thread the cars 3P belt beneth the cover of the childseat and lock the tongue into the buckle. Tighten after this
first the lap belt and then the shoulder belt as tight as possible.
15 Thread the blue locking clip beneth the cars 3P shoulder belt.
16. Tighten the shoulderbelt and lock the blue belt-lock.
17. Check that the cars 3P seat belt is mounted as shown on the image.
18. Attach the lower tether straps to the child seat.
19. Tighten as tight as possible the lower tether straps.
20. The buckle on the lower tether strap can be loosen by lifting it up. The seat can be dismounted in reversed
order.
21 - 22. Placing in the middle of the back seat. In some cars, the midle console prevents the correct mounting of
the load leg. If the load leg cannot be mounted like the image shows, the seat cannot be mounted on this place in
the car.
23 – 24. Mounting the lower tether straps on the passanger side.
25. The best way to mount the child seat in front on the passanger side is to place it against the dashbord, with
help of the load leg and recline tube. The child seat can also be mounted to the frontseat, with a 100mm space to
the dashboard. Please note, if placing the seat against the dashboard, some scratches can be caused by the metal
parts. Please use a soft towel to protect the dashboard.
Position the child into the seat
26. Push the button (A) to pull out the seat belt on the child seat. Pull out as long as possible the shoulder belts
(B). Open the belts by pressing the red button on the buckle (C), and pull the shoulder belt to the sides. Pull forward
the buckle part (E). Place the child into the seat (F), so that the buckle is placed between the legs of the child.
Mount the tongues (G) on the shoulderbelts together and lock them into the buckle (H). A clear "Click" noice shall
be heard. Adjust if needed the height of the shoulder belts (img. 2-3). Tighten the belts, by pulling straight out the
adjuster belt (I) The belt is correctly tightend when the adult manage to get two fingers between the child and the
belt. Check that the child is sitting safely in the seat.
NB! A seat mounted wrong can be dangerous in a possible accident.
11