Maintenance - Makita DTR180 Betriebsanleitung

3. Push the release lever, and lock it with the lock
lever.
► Fig.34: 1. Release lever 2. Lock lever
4. Remove the wire reel from the tool.
NOTE: When wire has been used up normally,
approximately 20 cm of the wire remains wound on
the reel. In this state, replace the wire reel with a new
one.
If it is difficult to remove the wire reel from the tool,
follow the steps below.
1. Insert the battery cartridge into the tool, and
turn the power on. The tool feeds the wire and cuts it
automatically.
2. Lock the trigger, turn the power off, and remove
the battery cartridge.
3.
Remove the wire breaks using tools such as nip-
pers or pliers.

MAINTENANCE

CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before attempting to perform inspection or
maintenance.
NOTICE:
Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
To maintain product SAFETY and RELIABILITY,
repairs, any other maintenance or adjustment should
be performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.
Storage of the hex wrench
Store the hex wrench in the position shown in the figure.
► Fig.35: 1. Hex wrench
Cleaning the cutter
When the tool is used for a long period of time, dust and
wire particles may become adhered to the cutter sec-
tion. In such a case, disassemble and clean the cutter
according to the following procedure.
If a wire is caught in the cutter section, the wire can be
removed by following the same procedure.
Disassembling and cleaning
1.
Loosen bolts A and B using the hex wrench
included in the tool package.
► Fig.36: 1. Bolt A 2. Bolt B 3. Contact plate cover
4. Wire guide B
NOTICE:
Do not forcibly remove any bolts that
cannot be removed using the hex wrench.
2. Pull the contact plate cover up in the direction of
the arrow and remove it. Bolt B will be removed at the
same time.
► Fig.37: 1. Contact plate cover 2. Bolt B
3. Remove bolt A, and remove wire guide B.
► Fig.38: 1. Bolt A 2. Wire guide B
4. Turn wire guide B over and clean its inside.
► Fig.39
5. Remove cutter A, cutter B, top plate, and link arm
A from arm plate A. Then, clean them.
► Fig.40: 1. Cutter B 2. Link arm A 3. Cutter A 4. Arm
plate A 5. Top plate
Assembling
When cleaning is finished, assemble the parts accord-
ing to the following procedure.
1. Install cutter A and link arm A to fit the shape of
arm plate A.
► Fig.41: 1. Cutter A 2. Link arm A 3. Arm plate A
2. Install cutter B and the top plate onto arm plate A.
(Install cutter B on cutter A and link arm A.)
► Fig.42: 1. Cutter B 2. Top plate 3. Arm plate A
4. Cutter A 5. Link arm A
NOTICE:
Face the projection of cutter B down-
ward, and install the cutter as shown in the figure.
3. Align the pipe of the tool with the groove inside the
wire guide B, and assemble them.
► Fig.43: 1. Pipe 2. Groove 3. Wire guide B
4. Fix wire guide B by temporarily tightening bolt A.
► Fig.44: 1. Bolt A 2. Wire guide B
5. Install the contact plate cover in the direction of
the arrow.
► Fig.45: 1. Contact plate cover
6.
Fix wire guide B and contact plate cover securely
by tightening bolt A and bolt B.
► Fig.46: 1. Wire guide B 2. Contact plate cover
3. Bolt A 4. Bolt B
7. After assembling, confirm that the contact plate
can move as shown in the figure.
► Fig.47: 1. Contact plate
NOTE: If the contact plate is caught, press it as
shown in the figure.
► Fig.48
17 ENGLISH