Herunterladen Inhalt Inhalt Diese Seite drucken

Residual Risks - Ryobi R18DDP2 Übersetzung Der Originalanleitung

Vorschau ausblenden Andere Handbücher für R18DDP2:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 9
Safety, performance, and dependability have been given
top priority in the design of your drill driver.
INTENDED USE
The drill driver is intended to be used only by adults who
have read and understood the instructions and warnings
in this manual, and can be considered responsible for their
actions.
The product can be used for drilling into various materials,
including wood, metal, and plastics using a drill bit having
a shank diameter of less than 13 mm. The product can
be used to drive and remove screws and bolts using an
appropriate bit.
Do not use the product in any way other than those stated
for intended use.
WARNING
Read all safety warnings, instructions, illustrations
and specifications provided with this power tool.
Failure to follow all instructions listed below may result in
Save all warnings and instructions for future reference.
DRILL DRIVER SAFETY WARNINGS
SAFETY INSTRUCTIONS FOR ALL OPERATIONS
Hold the power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory or fasteners may contact hidden wiring.
Cutting accessory or fasteners contacting a "live" wire
may make exposed metal parts of the power tool "live"
and could give the operator an electric shock.
SAFETY INSTRUCTIONS WHEN USING LONG DRILL
BITS
Never operate at higher speed than the maximum
speed rating of the drill bit. At higher speeds, the
bit is likely to bend if allowed to rotate freely without
Always start drilling at low speed and with the bit
tip in contact with the workpiece. At higher speeds,
the bit is likely to bend if allowed to rotate freely without
Apply pressure only in direct line with the bit and do
not apply excessive pressure. Bits can bend causing
ADDITIONAL SAFETY WARNINGS
Clamp
workpiece
with
damage.
Ambient temperature range for tool during operation is
between 0°C and 40°C.
Ambient temperature range for tool storage is between
0°C and 40°C.
The recommended ambient temperature range for the
charging system during charging is between 10°C and
38°C.
TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local and national
provisions and regulations.
Follow all special requirements on packaging and labelling
when transporting batteries by a third party. Ensure that
no batteries can come in contact with other batteries
or conductive materials while in transport by protecting
exposed connectors with insulating, non-conductive caps
or tape. Do not transport batteries that are cracked or
leaking. Check with the forwarding company for further
advice.
Even when the product is used as prescribed, it is still
impossible to completely eliminate certain residual risk
factors. The following hazards may arise and the operator
should pay special attention to avoid the following:
a
clamping
device.
It has been reported that vibrations from hand-held tools
may contribute to a condition called Raynaud's Syndrome
in certain individuals. Symptoms may include tingling,
upon exposure to cold. Hereditary factors, exposure to
cold and dampness, diet, smoking and work practices
are all thought to contribute to the development of these
ADDITIONAL BATTERY SAFETY WARNINGS
WARNING
damage due to a short circuit, never immerse your
as seawater, certain industrial chemicals, and bleach
or bleach-containing products, etc., can cause a short
circuit.
Ambient temperature range for battery during use is
between 0°C and 40°C.
Ambient temperature range for battery storage is
between 0°C and 20°C.

RESIDUAL RISKS

Damage to hearing caused by noise
Wear suitable hearing protection and limit exposure.
Wear protective eye shields or goggles when using
the product.
Limit exposure. Follow the instructions in Risk
Reduction.
Electric shock caused by contact with hidden wires
Hold the product only by insulated surfaces.
Dust created by operating the product can cause
mask with filters suitable for protecting against
particles from the material being worked on.
RISK REDUCTION
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR
EL
English |
1

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis