SOLAC CE4481 Gebrauchsanleitung Seite 12

GETTING HOT WATER:
Put the device in ON situation, pressing the
•
knob ON/OFF (F)
The Heating indicator light (D) will illuminate
•
indicating that the water is heating up.
Wait Until the pilot light (E) is also highlight-
•
ed. This situation indicates that the water has
reached the right temperature.
Place A container under the nozzle.
•
Open The steam control (R), turning him to the
•
left, counterclockwise
Press The button coffee /water outlet (G)
•
The Hot water began to come out of the va-
•
porizer.
Once obtained the desired amount of hot wa-
•
ter, press the coffee outlet button (G) again,
which stops the pump
Close The turning knob (R) to the right, clock-
•
wise
OBTAINING STEAM:
The steam is used to foam milk for cappuccino,
•
and also to heat other liquids.
Turn the appliance on using the on/off switch.
•
Wait until the pilot light (G) has gone out which
•
will indicate that the appliance has reached an
adequate temperature for making coffee
For Steam, press the Steam heating button (H)
•
and continue heating until the steam tempera-
ture has been reached.
The warning light (E) will illuminate indicating
•
that the water has reached the necessary tem-
perature for generating steam.
Place a recipient under the steam tube.
•
Open Steam knob (R) anticlockwise
•
Steam only will begin to exit.
•
When you have enough, close the control and
•
remove the recipient.
AUTOOFF FEATURE:
The SOLAC machines are designed to save
•
energy
To that end, after some minutes from the last
•
operation, the unit switches to energy saving
mode
To return to normal operation you should just
•
Switch OFF and Switch ON the connect button
(F)
ONCE YOU HAVE FINISHED USING THE
APPLIANCE:
Turn the appliance off, using the on/off switch
•
(F) to OFF
Unplug the appliance to the mains.
•
Remove the water from the water tank.
•
Clean the appliance
•
CLEANING
A. BASIC CLEANING
Disconnect the appliance from the mains and
•
let it cool before undertaking any cleaning task.
Clean the equipment with a damp cloth with a
•
few drops of washing-up liquid and then dry.
Do not use solvents, or products with an acid
•
or base pH such as bleach, or abrasive prod-
ucts, for cleaning the appliance.
Do not let water or any other liquid get into the
•
air vents to avoid damage to the inner parts of
the appliance.
Neither parts of this appliance are suitable for
•
cleaning in the dishwasher.
After washing, dry all the parts before fitting
•
them together and storing.
B. CLEANING THE FROTHING WAND
CAUTION! The frothing wand, frothing tip, and
•
frothing sleeve may be VERY HOT
It is recommended to purge and wipe the froth-
•
ing wand after steaming milk to prevent depos-
its of dirt and before turning off the machine
To do this, pull the black frothing sleeve down
•
Fill a cup with a bit of water, immerse the froth-
•
ing wand into the water
Drain hot water through the pipe, following the
•
instructions "Getting hot water"
Use a cloth to dry the frothing wand and re-
•
place the frothing sleeve
In case no steam comes out of the frothing
•
wand, hardened milk blocks its path.
Carefully use a needle to loosen the milk resi-
•
due from the opening of the frothing tube
to remove any blockage,
•
Once clean, rinse with running water from the
•
tap and reassemble it. Then steam again
HOW TO DEAL WITH LIME SCALE INCRUS-
TATIONS:
For the appliance to work correctly it should be
•
kept free of lime scale or magnesium incrusta-
tions caused by the use of hard water.
To prevent this kind of problem, we recom-
•
mend the use of water with low lime or magne-
sium mineralisation.
EN